$ Edit control commands, Used as the reference | Panasonic AJ-D250P

RS-232C

$Edit control commands

Sends data of computer			Return data from VTR		Description of command


	[STX] EAB:m [ETX]		[STX] EAB [ETX]	Sets whether auto back recording is to be performed to
Parameters				ensure frame to frame continuity.
m = N: AUTO BACK ON				<Note>
F: AUTO BACK OFF				This command is ignored while a search control command
				is being processed and during auto back.

	[STX] EAD:m [ETX]		[STX] EAD [ETX]	Sets the VTR to the AUDIO INSERT PAUSE mode.
Parameters				When the VTR is in the VIDEO INSERT PAUSE mode, the
m = 0: CH1 & CH2				command sets it to the AUDIO/VIDEO INSERT PAUSE
1: CH1				mode. When it is in the REC INHIBIT mode, error code
2: CH2				ER001 is returned from the VTR and the VTR is set to the
No parameter: CH1 & CH2				STOP mode.
				<Note>
				This command can be accepted when the VTR is in the
				PLAY PAUSE mode or STILL mode.

	[STX] EIN [ETX]		[STX] EIN [ETX]	Sets the VTR to the VIDEO INSERT PAUSE mode.
				When the VTR is in the AUDIO INSERT PAUSE mode, the
				command sets it to the AUDIO/VIDEO INSERT PAUSE
				mode. When it is in the REC INHIBIT mode, error code
				ER001 is returned from the VTR and the VTR is set to the
				STOP mode.
				<Note>
				This command can be accepted when the VTR is in the
				PLAY PAUSE mode or STILL mode.

	[STX] EFE:data [ETX]		[STX] EFE [ETX]	Initiates first edit (recording to prepare the tape to be used
Parameters				for editing).
data = wghmmssff				In order to conduct editing with the position designated by
w = M: Mode for recording for 26				the parameter as the reference point for editing, TC or CTL
	seconds			is preset using the value 23 seconds before the reference
E: Mode for recording as far				point, and the black burst video signal and muted audio
	as the tape end			signals are recorded for 26 seconds or until the tape end.
ghmmssff = Reference point during				If the OSP (STOP) command has been issued during
		editing (recording start		operation, error code ER123 will be returned from the VTR
		point)		which is then set to the STOP mode.
OWhen the CTL data is to be				If the VTR’s operation mode has been changed by
used as the reference				operating the controls on its front panel, error code ER121
g = Blank: With a positive value				will be returned from the VTR which is then set to the STOP
– sign: With a negative value				mode.
h =	0	9: Hours		If the tape end position is reached during operation, error
mm = 00		59: Minutes		code ER120 will be returned from the VTR which is then set
ss =	00	59: Seconds		to the STOP mode.
ff =	00	29: Frames		<Note>
OWhen the TC data is to be used				This command is ignored while a search control command
as the reference				is being processed and in any of the following modes.
gh =	00	23: Hours
					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE
mm = 00		59: Minutes

ss =	00	59: Seconds
ff =	00	29: Frames

<Note>

Make the menu item changes listed below when performing insert editing or assemble editing. If these changes are not made, the editing operations may not be conducted properly.

Menu item	Setting	Setting command

AUTO BACK	ON	EAB:N

TC MODE	I-REG	CTM:2

TCG REGEN	TC & UB	CRN:0

MEMORY MODE	OFF	SMM:F

STILL TIMER	2 min	TST:0200

50

Image 50

Panasonic AJ-D250P $ Edit control commands, OWhen the CTL data is to be, Used as the reference, As the reference

Contents

S0699W3119 a VQT8188-2 FCC Note Contents Features Introduction Counter display Parts and Their FunctionsFront panel ? Input Select switch Power switchLOCAL/MENU/REMOTE switch Cassette insertion slot Remote connector Headphones jackVolume control Reset button Connector panel REF Video in connector Signal GND terminalVideo in connector Audio in connectors Cassette Checkpoints for consumer-use DV tape playback TapesTape Description Operation Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape Check that the Stop lamp is lighted Stop mode Checkpoint for Still Timer setting Press the Stop button to end the recording RecordingPress the Play button while holding down the REC button Cue/review Pause/record frame-to-frame continuityPlayback Still picture playback Audio switching Frame by frame advance Repeat playback Setting the Begin and END points Menu modeSelect TC or CTL using the Counter button. Note Displaying the Begin and END points Setting the Begin and END points Front panelSetting the repeat playback mode User’s bit Time Codes and User’s BitTime codes TCR 00 07 04 Now follow the same procedure as for setting the time code Setting the time codeSetting the user’s bit Down button Stop button Playing back the time code/user’s bit 00 07 04 Characters displayed Superimposed ScreensDisplay position Superimpose Screens How to restore the factory settings Setup Initial SettingsHow to perform the settings using the on-screen menus How to set the user default settings How to load the user default settings How to initiate the menu protect mode How to release the menu protect mode How to display the Diag menu Underlining denotes the factory mode setting Setup MenusSetting Description of setting Superimposed Display System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Operation EditingPreparation Fading Audio editing functionsCutting Noise may appear here at the joins in the edit points First edit for insert editing First Edit Function Preparing the editing tapeFirst edit for assemble editing Communication parameters Interface specificationsRS-232C $ Data format External interface specificationsSending format computer VTR 3AH Receiving format VTR computer Example OAudio control commands Command list$ List of commands OCounter control commands OMedia operation control commands ODisplay control commandsOEdit control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands Parameters $ Audio control commands$ Counter control commands Sets the signal to be regenerated when the TCG time code TC data reference $ Display control commandsCTL data reference Menu item Setting Setting command $ Edit control commandsOWhen the CTL data is to be Used as the reference M1 HEX display M2 HEX display $ Media operation control commands$ Input/output control commands STX ORC ETX $ Operation control commandsSTX OBF ETX STX OSF ETX Case of a Dvcpro format tapeCase of a DV format tape Parameters OIn the case of a Dvcpro Format tape STX OSR ETX TC mode, UB mode, Remain mode $ Query control commandsCTL mode OIn the case of CTL data Ff = Frames Rewind Eject Auto Back OFF STX QHC ETXRewind Play Play Pause STX QHR ETX OWith no parameter Switching dataParameter M1 HEX display M2 HEX display Bits supported AD9ADAADBADCADDADEADF OSP StopAD AD AD AD AD Addressf OBitmap table a Cassette RF Video Tape Hard ACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETX OBitmap table B Video Option STX QVM ETX OWhen CTL data is to be used asReference OParameter setting no completion command $ Communication control commandsOParameter setting normal $ Search control commands OWhen CTL data is to be used OWhen the parameter value for Which the TC data serves as OWhen the counter value is toOWhen the parameter value for Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC Pause Audio Insert Pause Checkpoints for RS-232C communication $ Send commands and data returned from$ Send command intervals Error Messages Error No Description Procedure for removing the tape manually in an emergency Emergency Eject Condensation Video Head CleaningMaintenance $ Output connectors Specifications$ Input connectors $ Digital video $ Digital audio Page Southeast Region Executive OfficeMid-Atlantic/New England Central Region