$ Query control commands, CTL mode | Panasonic AJ-D250P manual

RS-232C

$ Query control commands

Sends data of computer		Return data from VTR			Description of command


[STX] QAL [ETX]		[STX] ALV0 [ETX]			Supports only address level 0 of the MIS standards.

[STX] QAO [ETX]		[STX] AOm [ETX]			Queries the audio signal output channel or channels.
	m = 1: CH1
	2: CH2
	3: CH3
	4: CH4
	5: CH1 & CH2
	6: CH3 & CH4
	7: CH1+3 & CH2+4

[STX] QCA [ETX]		[STX] CUPdata [ETX]			Queries the user’s bit data which was preset in the TCG.
	data = U7U6U5U4U7U3U2U1U0

[STX] QCB [ETX]		[STX] CUSdata [ETX]			Queries the user’s bit data of the TCG.
	data = U7U6U5U4U7U3U2U1U0

[STX] QCC [ETX]		[STX] CCPdata [ETX]			Queries the current counter data (second increments).
	data = ghmmss				The following data is returned from the VTR, depending on
	OIn the case of CTL data				the mode which appears on the counter display.
	g = Blank: With a positive value				CTL mode:
	– sign: With a negative value				CTL data
	h =	0	9:	Hours	TC mode, UB mode, REMAIN mode:
	mm = 00		59: Minutes		TC data
	ss =	00	59: Seconds
	OIn the case of TC data
	gh =	00	23: Hours
	mm = 00		59: Minutes
	ss =	00	59: Seconds

[STX] QCD [ETX]		[STX] CDdata [ETX]			Queries the current counter data.
	data = fwghmmssff				The following data is returned from the VTR, depending on
	OIn the case of CTL data				the mode which appears on the counter display.
	f =	F: Fine			CTL mode:
		C: Coarse			CTL data
	w =	S: Search STILL			TC mode, UB mode, REMAIN mode:
		P: Search PLAY			TC data
	g =	Blank: With a positive value
		– sign: With a negative value
	h =	0	9:	Hours
	mm = 00		59: Minutes
	ss =	00	59: Seconds
	ff =	00	29: Frames
	OIn the case of TC data
	f =	F: Fine
		C: Coarse
	w =	S: Search STILL
		P: Search PLAY
	gh =	00	23: Hours
	mm = 00		59: Minutes
	ss =	00	59: Seconds
	ff =	00	29: Frames

55

Image 55

Panasonic AJ-D250P $ Query control commands, OIn the case of CTL data, CTL mode, TC mode, UB mode, Remain mode

Contents

VQT8188-2 S0699W3119 a FCC Note Contents Introduction Features Front panel Parts and Their FunctionsCounter display Cassette insertion slot Power switchLOCAL/MENU/REMOTE switch ? Input Select switch Reset button Headphones jackVolume control Remote connector Connector panel Audio in connectors Signal GND terminalVideo in connector REF Video in connector Tape Description TapesCassette Checkpoints for consumer-use DV tape playback Check that the Stop lamp is lighted Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape Operation Checkpoint for Still Timer setting Stop mode Press the Play button while holding down the REC button RecordingPress the Stop button to end the recording Still picture playback Pause/record frame-to-frame continuityPlayback Cue/review Frame by frame advance Audio switching Select TC or CTL using the Counter button. Note Setting the Begin and END points Menu modeRepeat playback Setting the repeat playback mode Setting the Begin and END points Front panelDisplaying the Begin and END points TCR 00 07 04 Time Codes and User’s BitTime codes User’s bit Down button Stop button Setting the time codeSetting the user’s bit Now follow the same procedure as for setting the time code 00 07 04 Playing back the time code/user’s bit Display position Superimposed ScreensCharacters displayed Superimpose Screens How to perform the settings using the on-screen menus Setup Initial SettingsHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settings How to display the Diag menu How to release the menu protect mode System menu Setup MenusSetting Description of setting Superimposed Display Underlining denotes the factory mode setting Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Preparation EditingOperation Noise may appear here at the joins in the edit points Audio editing functionsCutting Fading First edit for assemble editing First Edit Function Preparing the editing tapeFirst edit for insert editing RS-232C Interface specificationsCommunication parameters 3AH External interface specificationsSending format computer VTR $ Data format Example Receiving format VTR computer OCounter control commands Command list$ List of commands OAudio control commands OInput/output control commands ODisplay control commandsOEdit control commands OMedia operation control commands OOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands $ Counter control commands $ Audio control commandsParameters Sets the signal to be regenerated when the TCG time code CTL data reference $ Display control commandsTC data reference Used as the reference $ Edit control commandsOWhen the CTL data is to be Menu item Setting Setting command $ Input/output control commands $ Media operation control commandsM1 HEX display M2 HEX display STX OBF ETX $ Operation control commandsSTX ORC ETX Parameters OIn the case of a Dvcpro Format tape Case of a Dvcpro format tapeCase of a DV format tape STX OSF ETX STX OSR ETX OIn the case of CTL data $ Query control commandsCTL mode TC mode, UB mode, Remain mode Ff = Frames Rewind Play Play Pause STX QHR ETX Auto Back OFF STX QHC ETXRewind Eject Parameter M1 HEX display M2 HEX display Bits supported Switching dataOWith no parameter Addressf OSP StopAD AD AD AD AD AD9ADAADBADCADDADEADF Cassette RF Video Tape Hard OBitmap table a Repeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETX OBitmap table B Reference OWhen CTL data is to be used asVideo Option STX QVM ETX OParameter setting normal $ Communication control commandsOParameter setting no completion command OWhen CTL data is to be used $ Search control commands Be stored in the memory OWhen the counter value is toOWhen the parameter value for OWhen the parameter value for Which the TC data serves as OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition table Insert Pause Audio $ Send command intervals $ Send commands and data returned fromCheckpoints for RS-232C communication Error No Description Error Messages Emergency Eject Procedure for removing the tape manually in an emergency Maintenance Video Head CleaningCondensation $ Digital video Specifications$ Input connectors $ Output connectors $ Digital audio Page Central Region Executive OfficeMid-Atlantic/New England Southeast Region