Panasonic AJ-D250P specs

RS-232C

$Counter control commands

Sends data of computer			Return data from VTR		Description of command


	[STX] CLP:data [ETX]		[STX] CLP [ETX]	Presets the designated counter value on the CTL counter.
Parameters				The value will be corrected as follows if the non-drop frame
data = ghmmssff				preset value has been set while the drop frame mode is
g = Blank: With a positive value				established.
– sign: With a negative value				00:01:00:00	00:00:59:28
h =	0	9: Hours		00:01:00:01	00:00:59:29
mm = 00		59: Minutes		<Note>
ss =	00	59: Seconds		This command is ignored while a search control command
ff =	00	29: Frames		is being processed or while the tape is being ejected.

	[STX] CRN:m [ETX]		[STX] CRN [ETX]	Sets the signal to be regenerated when the TCG (time code
Parameters				generator) is set to the regeneration mode.
m = 0: TC & UB				<Note>
1: TC				This command is ignored while a search control command
2: UB				is being processed.

	[STX] CRR [ETX]		[STX] CRR [ETX]	Uses the TCG in the REC RUN mode. The TCG counts up
				during recording. The default value can be set using the
				CTS command.
				<Note>
				This command is ignored while a search control command
				is being processed, during recording and in the INSERT
				mode.

	[STX] CRT [ETX]		[STX] CRT [ETX]	Resets the CTL counter data.
				<Note>
				This command is ignored while a search control command
				is being processed.

	[STX] CTC [ETX]		[STX] CTC [ETX]	Uses the reference data for searching and for the display
				mode of the counter display as the time code data.
				<Note>
				This command is ignored while a search control command
				is being processed.

	[STX] CTF [ETX]		[STX] CTF [ETX]	Uses the TCG in the FREE RUN mode.
				The TCG continues to count up at all times regardless of
				the mode. The default value can be set using the CTS
				command.
				The TCG starts counting up upon completion of the settings
				and when the VTR’s power is turned back on.
				<Note>
				This command is ignored while a search control command
				is being processed, during recording and in the INSERT
				mode.

	[STX] CTL [ETX]		[STX] CTL [ETX]	Uses the reference data for searching and for the display
				mode of the counter display as the CTL data.
				<Note>
				This command is ignored while a search control command
				is being processed.

	[STX] CTM:m [ETX]		[STX] CTM [ETX]	Sets the mode used by the TCG.
Parameters				<Note>
m = 0: REC RUN mode				This command is ignored while a search control command
1: FREE RUN mode				is being processed, during recording and in the INSERT
2: Regeneration mode				mode.
3: External VITC mode

48

Image 48

Panasonic AJ-D250P operating instructions Sets the signal to be regenerated when the TCG time code

Contents

S0699W3119 a VQT8188-2 FCC Note Contents Features Introduction Parts and Their Functions Front panelCounter display Power switch LOCAL/MENU/REMOTE switch? Input Select switch Cassette insertion slot Headphones jack Volume controlRemote connector Reset button Connector panel Signal GND terminal Video in connectorREF Video in connector Audio in connectors Tapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Turning on the power/inserting a cassette Turn on the unit’s power Insert the cassette tapeOperation Check that the Stop lamp is lighted Stop mode Checkpoint for Still Timer setting Recording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Pause/record frame-to-frame continuity PlaybackCue/review Still picture playback Audio switching Frame by frame advance Setting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points Time Codes and User’s Bit Time codesUser’s bit TCR 00 07 04 Setting the time code Setting the user’s bitNow follow the same procedure as for setting the time code Down button Stop button Playing back the time code/user’s bit 00 07 04 Superimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to load the user default settings How to initiate the menu protect mode How to release the menu protect mode How to display the Diag menu Setup Menus Setting Description of setting Superimposed DisplayUnderlining denotes the factory mode setting System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Audio editing functions CuttingFading Noise may appear here at the joins in the edit points First Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters External interface specifications Sending format computer VTR$ Data format 3AH Receiving format VTR computer Example Command list $ List of commandsOAudio control commands OCounter control commands ODisplay control commands OEdit control commandsOMedia operation control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands $ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference $ Edit control commands OWhen the CTL data is to beMenu item Setting Setting command Used as the reference $ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Case of a Dvcpro format tape Case of a DV format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tape STX OSR ETX $ Query control commands CTL modeTC mode, UB mode, Remain mode OIn the case of CTL data Ff = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter OSP Stop AD AD AD AD ADAD9ADAADBADCADDADEADF Addressf OBitmap table a Cassette RF Video Tape Hard ACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETX OBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command $ Search control commands OWhen CTL data is to be used OWhen the counter value is to OWhen the parameter value forOWhen the parameter value for Which the TC data serves as Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC Pause Audio Insert Pause $ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error Messages Error No Description Procedure for removing the tape manually in an emergency Emergency Eject Video Head Cleaning MaintenanceCondensation Specifications $ Input connectors$ Output connectors $ Digital video $ Digital audio Page Executive Office Mid-Atlantic/New EnglandSoutheast Region Central Region