Superimposed Screens, Display position | Panasonic AJ-D250P instruction

Superimposed Screens

When the unit’s MONITOR OUT connector has been connected to a TV monitor, the control signals, time codes, etc. are displayed on the TV monitor screen as abbreviations.

The display can be switched ON or OFF using the setup menu item No. 000 setting. (See page 28)

Display position

The position where the superimposed display appears can be changed using setup menu item No.002 “CHARA H-POS” and No.003 (CHARA V-POS).

(See page 28)

TV monitor

TCR: : :

No display:

Normally, no display

S: Appears with FAN STOP.

L: Appears with LOW RF.

N: Appears with NO RF.

TCR : : :

TCR : : :

TV monitor

TV monitor

Abbreviation

CTL: control signal

TCR: time code playback value

UBR: user’s bit playback value

REM: remaining tape amount

Characters displayed

The background of the characters superimposed onto the display can be changed using the setup menu item No.004 “CHARA TYPE” setting. (See page 28)

<Note>

When the MODE button and the DATA+ button or DATA– button are pressed, the counter display appears temporarily while the buttons are held down so that the setting can be checked.

Even while the MODE button is held down, settings can still be performed using the DATA+ button or DATA– button as the actual status is checked.

TCR	: : :	TCR	: : :
	TV monitor		TV monitor

21

Image 21

Panasonic AJ-D250P operating instructions Superimposed Screens, Display position, Characters displayed

Contents

VQT8188-2 S0699W3119 a FCC Note Contents Introduction Features Parts and Their Functions Front panelCounter display LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slot Volume control Headphones jackRemote connector Reset button Connector panel Video in connector Signal GND terminalREF Video in connector Audio in connectors Tapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lighted Checkpoint for Still Timer setting Stop mode Recording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Playback Pause/record frame-to-frame continuityCue/review Still picture playback Frame by frame advance Audio switching Setting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04 Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button 00 07 04 Playing back the time code/user’s bit Superimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settings How to display the Diag menu How to release the menu protect mode Setting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit points First Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters Sending format computer VTR External interface specifications$ Data format 3AH Example Receiving format VTR computer $ List of commands Command listOAudio control commands OCounter control commands OEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands $ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference $ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tape STX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL data Ff = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF Addressf Cassette RF Video Tape Hard OBitmap table a Repeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETX OBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command OWhen CTL data is to be used $ Search control commands OWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition table Insert Pause Audio $ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error No Description Error Messages Emergency Eject Procedure for removing the tape manually in an emergency Video Head Cleaning MaintenanceCondensation $ Input connectors Specifications$ Output connectors $ Digital video $ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region