$ Search control commands | Panasonic AJ-D250P manual

RS-232C

$Search control commands

Sends data of computer				Return data from VTR		Description of command


	[STX] SCP:data [ETX]			[STX] SCP [ETX]	Searches the counter value which was designated by the
Parameters					parameter.
data = ghmmssff					Playback is commenced upon completion of the search.
OWhen CTL data is to be used					If the designated position is an illegal position (the target
as the reference					position does not exist), error code ER122 will be returned
g = Blank: With a positive value					from the VTR, which is then set to the STOP mode.
– sign: With a negative value					When the OSP (STOP) command or OEJ (tape EJECT)
h =	0	9:	Hours		command is issued during operation, error code ER123 is
mm = 00		59: Minutes			returned from the VTR.
ss =	00	59: Seconds			If the VTR’s operation mode has been changed by
ff =	00	29: Frames			operating the controls on its front panel, error code ER121
OWhen TC data is to be used as					will be returned from the VTR.
the reference					If the tape end position is reached during operation, error
gh =	00	23: Hours			code ER120 will be returned from the VTR.
mm = 00		59: Minutes			When data differing from the data used as the reference
ss =	00	59: Seconds			has been sent, error code ER001 will be returned from the
ff =	00	29: Frames			VTR.
					<Note>
					This command is ignored while a search control command
					is being processed and in any of the following modes.

						EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE


	[STX] SCS:data [ETX]			[STX] SCS [ETX]	Searches the counter value which was designated by the
Parameters					parameter.
data = ghmmssff					The STILL mode is established upon completion of the
OWhen CTL data is to be used					search.
as the reference					If the designated position is an illegal position (the target
g = Blank: With a positive value					position does not exist), error code ER122 will be returned
– sign: With a negative value					from the VTR which is then set to the STOP mode.
h =	0	9:	Hours		When the OSP (STOP) command or OEJ (tape EJECT)
mm = 00		59: Minutes			command is issued during operation, error code ER123 is
ss =	00	59: Seconds			returned from the VTR.
ff =	00	29: Frames			If the VTR’s operation mode has been changed by
OWhen TC data is to be used as					operating the controls on its front panel, error code ER121
the reference					will be returned from the VTR.
gh =	00	23: Hours			If the tape end position is reached during operation, error
mm = 00		59: Minutes			code ER120 will be returned from the VTR.
ss =	00	59: Seconds			When data differing from the data used as the reference
ff =	00	29: Frames			has been sent, error code ER001 will be returned from the
					VTR.
					<Note>
					This command is ignored while a search control command
					is being processed and in any of the following modes.

						EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE

65

Image 65

Panasonic AJ-D250P operating instructions $ Search control commands, OWhen CTL data is to be used

Contents

VQT8188-2 S0699W3119 a FCC Note Contents Introduction Features Counter display Parts and Their FunctionsFront panel LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slot Volume control Headphones jackRemote connector Reset button Connector panel Video in connector Signal GND terminalREF Video in connector Audio in connectors Cassette Checkpoints for consumer-use DV tape playback TapesTape Description Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lighted Checkpoint for Still Timer setting Stop mode Press the Stop button to end the recording RecordingPress the Play button while holding down the REC button Playback Pause/record frame-to-frame continuityCue/review Still picture playback Frame by frame advance Audio switching Repeat playback Setting the Begin and END points Menu modeSelect TC or CTL using the Counter button. Note Displaying the Begin and END points Setting the Begin and END points Front panelSetting the repeat playback mode Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04 Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button 00 07 04 Playing back the time code/user’s bit Characters displayed Superimposed ScreensDisplay position Superimpose Screens How to restore the factory settings Setup Initial SettingsHow to perform the settings using the on-screen menus How to set the user default settings How to initiate the menu protect mode How to load the user default settings How to display the Diag menu How to release the menu protect mode Setting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Operation EditingPreparation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit points First edit for insert editing First Edit Function Preparing the editing tapeFirst edit for assemble editing Communication parameters Interface specificationsRS-232C Sending format computer VTR External interface specifications$ Data format 3AH Example Receiving format VTR computer $ List of commands Command listOAudio control commands OCounter control commands OEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands Parameters $ Audio control commands$ Counter control commands Sets the signal to be regenerated when the TCG time code TC data reference $ Display control commandsCTL data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference M1 HEX display M2 HEX display $ Media operation control commands$ Input/output control commands STX ORC ETX $ Operation control commandsSTX OBF ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tape STX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL data Ff = Frames Rewind Eject Auto Back OFF STX QHC ETXRewind Play Play Pause STX QHR ETX OWith no parameter Switching dataParameter M1 HEX display M2 HEX display Bits supported AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF Addressf Cassette RF Video Tape Hard OBitmap table a Repeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETX OBitmap table B Video Option STX QVM ETX OWhen CTL data is to be used asReference OParameter setting no completion command $ Communication control commandsOParameter setting normal OWhen CTL data is to be used $ Search control commands OWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition table Insert Pause Audio Checkpoints for RS-232C communication $ Send commands and data returned from$ Send command intervals Error No Description Error Messages Emergency Eject Procedure for removing the tape manually in an emergency Condensation Video Head CleaningMaintenance $ Input connectors Specifications$ Output connectors $ Digital video $ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region