$ Display control commands, CTL data reference | Panasonic AJ-D250P

RS-232C

$Counter control commands

Sends data of computer			Return data from VTR		Description of command


	[STX] CTP [ETX]		[STX] CTP [ETX]	Uses the TCG in the preset mode.
				The TCG starts counting up in the REC RUN mode upon
				completion of the settings.
				<Note>
				This command is ignored while a search control command
				is being processed, during recording and in the INSERT
				mode.

	[STX] CTR [ETX]		[STX] CTR [ETX]	Uses the TCG in the regeneration mode.
				<Note>
				This command is ignored while a search control command
				is being processed, during recording and in the INSERT
				mode.

	[STX] CTS:data [ETX]		[STX] CTS [ETX]	Presets the TCG data.
Parameters				The value will be corrected as follows if the non-drop frame
data = hhmmssff				preset value has been set while the drop frame mode is
hh =	00	23: Hours		established.
mm = 00		59: Minutes		00:01:00:00	00:00:59:28
ss =	00	59: Seconds		00:01:00:01	00:00:59:29
ff =	00	29: Frames		Error code ER001 is returned from the VTR when the TCG
				is used in the regeneration mode or external VITC mode.
				<Note>
				This command is ignored while a search control command
				is being processed.

	[STX] CUS:data [ETX]		[STX] CUS [ETX]	Presets the user’s bit data in the TCG.
Parameters				Error code ER001 is returned from the VTR when the TCG
data = U7U6U5U4U7U3U2U1U0				is used in the regeneration mode or external VITC mode.
The input user bit data is set in				<Note>
ASCII code.				This command is ignored while a search control command
UB data: Binary 4BITa8				is being processed.
ASCII code:		0 9, A F

	[STX] CVP:data [ETX]		[STX] CVP [ETX]	Specifies two lines where the external VITC signal is to be
Parameters				inserted.
data = ppqq				<Note>
pp = 10 20: Insertion line 1				This command is ignored while a search control command
qq = 10 20: Insertion line 2				is being processed, during recording and in the INSERT
pp ≠ qq				mode.
(the same value cannot be
designated for both pp and qq)

$Display control commands

Sends data of computer	Return data from VTR	Description of command


[STX] DFC:m [ETX]	[STX] DFC [ETX]	Sets the display mode of the counter display and the
Parameters		reference data for searching.
m = C: CTL mode		CTL data reference:
T: TC mode		CTL mode
U: UB mode		TC data reference:
R: REMAIN mode		TC mode, UB mode, REMAIN mode
		<Note>
		This command is ignored while a search control command
		is being processed.

49

Image 49

Panasonic AJ-D250P operating instructions $ Display control commands, CTL data reference, TC data reference

Contents

VQT8188-2 S0699W3119 a FCC Note Contents Introduction Features Front panel Parts and Their FunctionsCounter display LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slot Volume control Headphones jackRemote connector Reset button Connector panel Video in connector Signal GND terminalREF Video in connector Audio in connectors Tape Description TapesCassette Checkpoints for consumer-use DV tape playback Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lighted Checkpoint for Still Timer setting Stop mode Press the Play button while holding down the REC button RecordingPress the Stop button to end the recording Playback Pause/record frame-to-frame continuityCue/review Still picture playback Frame by frame advance Audio switching Select TC or CTL using the Counter button. Note Setting the Begin and END points Menu modeRepeat playback Setting the repeat playback mode Setting the Begin and END points Front panelDisplaying the Begin and END points Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04 Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button 00 07 04 Playing back the time code/user’s bit Display position Superimposed ScreensCharacters displayed Superimpose Screens How to perform the settings using the on-screen menus Setup Initial SettingsHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settings How to display the Diag menu How to release the menu protect mode Setting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menu Basic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Preparation EditingOperation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit points First edit for assemble editing First Edit Function Preparing the editing tapeFirst edit for insert editing RS-232C Interface specificationsCommunication parameters Sending format computer VTR External interface specifications$ Data format 3AH Example Receiving format VTR computer $ List of commands Command listOAudio control commands OCounter control commands OEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commands OOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands $ Counter control commands $ Audio control commandsParameters Sets the signal to be regenerated when the TCG time code CTL data reference $ Display control commandsTC data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference $ Input/output control commands $ Media operation control commandsM1 HEX display M2 HEX display STX OBF ETX $ Operation control commandsSTX ORC ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tape STX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL data Ff = Frames Rewind Play Play Pause STX QHR ETX Auto Back OFF STX QHC ETXRewind Eject Parameter M1 HEX display M2 HEX display Bits supported Switching dataOWith no parameter AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF Addressf Cassette RF Video Tape Hard OBitmap table a Repeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETX OBitmap table B Reference OWhen CTL data is to be used asVideo Option STX QVM ETX OParameter setting normal $ Communication control commandsOParameter setting no completion command OWhen CTL data is to be used $ Search control commands OWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memory OWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition table Insert Pause Audio $ Send command intervals $ Send commands and data returned fromCheckpoints for RS-232C communication Error No Description Error Messages Emergency Eject Procedure for removing the tape manually in an emergency Maintenance Video Head CleaningCondensation $ Input connectors Specifications$ Output connectors $ Digital video $ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region