Cobra Electronics MRHH325VP Product Features, Channel Scan Mode, Memory Location Scan Mode

Page 32

Operating Your Radio

Scanning

SCAN Button

SCAN Icon

Channel Up/Down Button

56 English

Product Features

Channel Scan Mode

During Channel Scan mode, the radio will rapidly switch from channel to channel through all the channels. Whenever any activity is detected, the radio will stop the scan for 10 seconds to allow you to listen briefly on that channel. The radio will then continue to scan unless you sw itch out of the Channel Scan mode.

NOTE

The radio must be squelched for Channel Scan mode to function. See page 37 for Squelch procedure.

To Enter Channel Scan:

1.From Marine Standby mode, press the SCAN button. The radio will immediately begin to scan the entire channel map selected in the active channel map. The SCAN icon will show on the LCD.

2.A signal on any channel will stop the scan for 10 seconds to allow you to listen to the traffic on that location.

3.Press the Channel Up/Down button to resume scanning the Channel Scan channels or to change the scan direction.

4.To EXIT Channel Scan mode, press the SCAN button again. The SCAN icon will disappear from the LCD and the radio will return to Marine Standby mode.

Operating Your Radio

Memory Location Scan

A

A

Product Features

Memory Location Scan Mode

During Memory Location Scan mode, the radio will rapidly scan through all pre-assigned memory channels. Whenever any activity is detected on a channel, the radio will stop the scan for 10 seconds to allow you to listen briefly on that channel. It will then continue to scan unless you switch out of Memory Location Scan mode.

NOTE

The radio must be squelched for Memory Location Scan mode to function. See page 37 for Squelch procedure.

NOTE

If there are fewer than two (2) memory locations programmed in the radio, the Memory Location Scan option will not be available. To program at least two

(2) memory locations, see page 54.

Nothing Comes Close to a Cobra® 57

Image 32

Contents For Assistance Outside the U.S.A Our Thanks to You Customer AssistanceCustomer Assistance For Assistance in the U.S.A Radio Controls Indicators Backlit LCD Screen Product FeaturesProduct Features Backlit LCD Liquid Crystal Display ScreenSignal Strength Meter Emergency Weather AlertSpeaker/Mic Jack Unlimited Memory Channels Roger Beep Tone SelectableTable of Contents Important Safety Information Important Safety InformationSafety Training Information Recommendations for Marine Communication Recommendations for Marine CommunicationFCC Licensing Information VHF Marine Radio Procedures Voice Calling Voice CallingVoice Calling Vessel Corsair is calling the vessel VagabondEmergency Messages Distress Procedure Emergency Messages and Distress ProcedureRadiotelephone Calls Radiotelephone CallsIf You Hear a Distress Call Marine Emergency SignalsMarine Distress Procedure Emergency Messages and Distress Procedure VHF Marine Channel Assignments 03A Government Only International Distress, Safety and CallingVHF Marine Channel Assignments 23A Government Only 20A Port Operations Port Operations, Ship Movement21A U.S. Government Only Canada Coast Guard Only 64A U.S. Government Only Canada Commercial Fishing Digital Selective Calling Voice communications not allowed81A U.S. Government Only Environmental Protection Operations Noaa Weather Channels Alert Noaa Emergency Weather AlertNoaa Test Alert System Weather Frequency/ChannelBelt Clip Included in this PackageAntenna, Wrist Strap Batteries and Charger Batteries and ChargerInitial Charge Maintaining the Battery Charge Alkaline BatteriesPower/Volume/Squelch Controls Power On/Off Control Getting StartedCommon Radio Functions Getting StartedBacklight/Key Lock Button Scan ButtonSetup Mode Programming Setup Mode ProgrammingHigh/Medium/Low H-M-L Power Button To Toggle Between H-M-L Power ModesVibrAlert Mode USA/International/Canada Channel MapsTo Set Channel Map Operating Area To set VibrAlertCall Tone Mode Roger Beep ModeKey Tone Mode Standby/Receive TransmitMarine Standby and Receive Rx Mode Standby/Receive and TransmitTo Set WX Alert On or Off To Set WX Auto Search Scan On or OffTransmit Tx Mode Weather WX Standby ModeWX Alert Standby Mode To Transmit a MessageAdvanced Operation Channel 16/9 ModeAdvanced Operation Tri-Watch Mode Tri-Watch Setup To Program or Edit the Tri-Watch ChannelsUsing Tri-Watch Tri-Watch Scan Mode Advanced OperationMemory Location Mode To Exit Memory Location ModeTo Program Memory Locations To Recall a Stored Memory LocationProduct Features Channel Scan ModeMemory Location Scan Mode To Enter Channel ScanTroubleshooting Maintenance TroubleshootingMaintenance Warranty and Trademark Specifications Acknowledgement Specifications Limited 3-Year WarrantyFor Products Purchased In The U.S.A For Products Purchased Outside The U.S.AAccessories Product ServiceAccessories