Manuals / Intel / Computer Equipment / Switch

Intel IXF1104 manual 5.8.6.1LED Signaling Behavior, Fiber LED Behavior, Datasheet

Models: IXF1104

1 227

Download 227 pages 3.32 Kb

Page 118

5.8.6.1LED Signaling Behavior

IXF1104 Quad-Port 10/100/1000 Mbps Ethernet Media Access Controller

Note: The data decode of the LED bits is independent of the Physical mode selection.

Table 34. LED_DATA# Decodes

LED_DATA#	MAC Port #	Fiber Designation	Copper Designation

1		Rx LED—Amber	Link LED—Amber

2	0	Rx LED—Green	Link LED—Green

3		TX LED—Green	Activity LED—Green

4		Rx LED—Amber	Link LED—Amber

5	1	Rx LED—Green	Link LED—Green

6		TX LED—Green	Activity LED—Green

7		Rx LED—Amber	Link LED—Amber

8	2	Rx LED—Green	Link LED—Green

9		TX LED—Green	Activity LED—Green

10		Rx LED—Amber	Link LED—Amber

11	3	Rx LED—Green	Link LED—Green

12		TX LED—Green	Activity LED—Green

5.8.6.1LED Signaling Behavior

Operation in each mode for the decoded LED data in Table 34 is detailed in Table 35 and Table 36.

5.8.6.1.1 Fiber LED Behavior

Table 35. LED Behavior (Fiber Mode)

	Type	Status	Description

		Off	Synchronization occurs but no packets are received
		Off	and the “Link LED Enable ($0x502)” is not set.
			and the “Link LED Enable ($0x502)” is not set.

		Amber On	RX Synchronization has not occurred or no optical
		Amber On	signal exists.
			signal exists.

			The port has remote fault and the “Link LED Enable
	RXLED	Amber Blinking	($0x502)” is not set (based on remote fault bit setting
			received in Rx_Config word).

		Green On	RX Synchronization occurs and the “Link LED Enable
		Green On	($0x502)” bit is set.
			($0x502)” bit is set.

		Green Blinking	RX Synchronization occurs and the port is receiving
		Green Blinking	data.
			data.

		Off	The port is not transmitting data or the “Link LED
		Off	Enable ($0x502)” is not set.
	TXLED		Enable ($0x502)” is not set.

		Green Blinking	The port is transmitting data and the “Link LED Enable
			The port is transmitting data and the “Link LED Enable
			($0x502)” bit is set
			($0x502)” bit is set

NOTE: Table 35 assumes the port is enabled in the “Port Enable ($0x500)” and the LEDs are enabled in the “LED Control ($0x509)”. If a port is not enabled, all the LEDs for that port will be off. If the LEDs are not enabled, all of the LEDs will be off.

118

Datasheet

Document Number: 278757

Revision Number: 007

Revision Date: March 25, 2004

Image 118

Intel IXF1104 manual 5.8.6.1LED Signaling Behavior, Fiber LED Behavior, Datasheet

Contents

Product Features DatasheetDatasheet ApplicationsContents ContentsIntroduction DatasheetContents DatasheetContents DatasheetContents ApplicationsDatasheet Contents Figures10.0 DatasheetContents TablesDatasheet Contents DatasheetContents DatasheetContents DatasheetContents Revision HistoryDatasheet Revision Number: ContentsDatasheet Revision Date: March 25,Contents DatasheetRevision Number: Revision Date: March 25, ContentsDatasheet Sheet 4 of Page # DescriptionRevision Number: Revision Date: March 25, ContentsDatasheet Sheet 5 ofContents DatasheetContents Datasheet1.2Related Documents 1.0Introduction1.1What You Will Find in This Document Datasheet2.0General Description DatasheetDatasheet Figure 2. Internal ArchitectureDatasheet 3.0Ball Assignments and Ball List Tables3.1Ball Assignments = No Pad A11.GMII Ball Connection 3.Fiber Mode Ball Connection3.2Ball List Tables 2.SPI3 Ball ConnectionDatasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Document Number: Revision Number: DatasheetRevision Date: March 25, 4.1.1Signal Name Conventions 4.0Ball Assignments and Signal Descriptions4.1Naming Conventions DatasheetSPHY MPHY 4.2Interface Signal GroupsDatasheet GMIIMode 4.3Signal Description TablesDatasheet BitsTransmit Error DatasheetTransmit Write Enable Transmit Parity32-bit Multi-PHYmode: TMOD1:0 DatasheetTMOD1:0 Transmit Word Modulo 4 x 8 Single-PHYmode: MOD1:0 is notDTPA_0:3 Direct Transmit Packet DatasheetAvailable Receive Data Bus DatasheetPolled-PHYTransmit Packet Available ModeReceive Data Bus DatasheetReceive Read Enable Mode32-bit Multi-PHYmode: RERR_0 covers DatasheetReceive Error 4 x 8 Single-PHYmode: The RERR_0:332-bit Multi-PHYmode: REOP_0 covers DatasheetReceive End of Packet 4 x 8 Single-PHYmode: The REOP_0:3Table 4. SerDes Interface Signal Descriptions DatasheetTransmit Error DatasheetTransmit Enable Transmit DataReceive Data DatasheetReceive Error Receive Data ValidTransmit Data DatasheetSource Synchronous Transmit Clock Transmit ControlReceive Data DatasheetReceive Control Data bus DatasheetCycle complete indicator 32-bitmode: Uses 31:0Transmit Disable DatasheetReceiver Loss of Signal Interrupt Transmitter Fault Interrupt Table 10. MDIO Interface Signal DescriptionsDatasheet Module Definition InterruptTable 13. System Interface Signal Descriptions Table 11. LED Interface Signal DescriptionsTable 12. JTAG Interface Signal Descriptions DatasheetTable 14. Power Supply Signal Descriptions DatasheetDatasheet 4.4Ball Usage SummaryTotal 4.5Multiplexed Ball Connections Datasheet4.5.2SPI3 MPHY/SPHY Ball Connections DatasheetDatasheet Table 17. SPI3 MPHY/SPHY Interface Sheet 2 of4.6Ball State During Reset DatasheetDatasheet 4.7.2Power-DownSequence 4.7Power Supply Sequencing4.7.1Power-UpSequence Datasheet4.8Pull-Up/Pull-DownBall Guidelines 4.9Analog Power FilteringDatasheet 2.5 or 1.8 Power BallDatasheet Analog5.0Functional Descriptions 5.1Media Access Controller MACDatasheet 5.1.1.2Automatic CRC Generation 5.1.1Features for Fiber and Copper Mode5.1.1.1Padding of Undersized Frames on Transmit 5.1.1.3Filtering of Receive Packets5.1.1.3.3Filter Broadcast Packets 5.1.1.3.6Filter CRC Error Packets5.1.1.3.2Filter on Multicast Packet Match 5.1.1.3.4Filter VLAN Packets5.1.2Flow Control 5.1.1.4CRC Error DetectionDatasheet 5.1.2.1802.3x Flow Control Full-DuplexOperation DatasheetSPI3 Interface 5.1.2.1.1Pause Frame FormatDatasheet 5.1.2.1.2Pause Settings Datasheet5.1.2.1.5Transmit Pause Control Interface 5.1.2.1.4Half-DuplexOperationDatasheet “FC TX Timer Value $ Port_Index + 0x07 XOFF “FC TX Timer Value $ Port_Index + 0x07 XOFF“FC TX Timer Value $ Port_Index + 0x07 XOFF “FC TX Timer Value $ Port_Index + 0x07 XOFF5.1.3Mixed-ModeOperation 5.1.3.1Configuration of the IXF11045.1.3.2Key Configuration Registers Datasheet5.1.4Fiber Mode Datasheet5.1.4.1Fiber Auto-Negotiation 5.1.5Copper Mode5.1.4.3Fiber Forced Mode Datasheet5.1.5.2Duplex 5.1.6Jumbo Packet Support5.1.5.1Speed 5.1.5.3Copper Auto-Negotiation5.1.6.3Loss-lessFlow Control 5.1.6.1Rx Statistics5.1.6.2TX Statistics Datasheet5.1.7.1TX and RX FIFO Operation 5.1.7.1.1TX FIFO 5.1.7Packet Buffer Dimensions5.1.8RMON Statistics Support 5.1.7.1.2RX FIFODatasheet Table 25. RMON Additional Statistics Sheet 1 of5.1.8.1Conventions Datasheet5.1.8.2IXF1104 Advantages 5.2SPI3 InterfaceDatasheet Data Path 5.2.1MPHY Operation5.2.2MPHY Logical Timing 5.2.1.1SPI3 RX Round Robin Data Transmission5.2.2.2Receive Timing 5.2.2.1Transmit TimingDatasheet IXF1104 MPHY DatasheetNetwork Processor Line-SideInterface5.2.2.4Parity 5.2.2.5SPHY Mode5.2.2.3Clock Rates 5.2.2.5.1Data Path5.2.2.8Receive Timing SPHY 5.2.2.6SPHY Logical Timing5.2.2.7Transmit Timing SPHY DatasheetDatasheet Figure 15. SPHY Receive Logical Timing5.2.2.8.1Clock Rates Datasheet5.2.2.9.1RX SPI3 Flow Control 5.2.2.8.2Parity5.2.2.9SPI3 Flow Control 5.2.2.9.2TX SPI3 Flow ControlPTPA DTPA_0:3STPA Datasheet5.2.3Pre-PendingFunction 5.3Gigabit Media Independent Interface GMIIDatasheet 5.3.2GMII Interface Signal Definition 5.3.1GMII Signal MultiplexingDatasheet Transmit Error DatasheetTransmit Enable Receive ErrorIntel IXF1104 Media Access Controller5.4.1Multiplexing of Data and Control Quad PHY Device5.4.3TX_ER and RX_ER Coding 5.4.2Timing SpecificsDatasheet TD3:0_0:3 DatasheetTXC_0:3 TX_CTL_0:35.4.3.1In-BandStatus 5.5MDIO Control and Interface5.4.410/100 Mbps Functionality Datasheet5.5.2MDIO Register Descriptions 5.5.3Clear When Done5.5.1MDIO Address 5.5.4MDC Generation5.5.7MDI State Machine 5.5.6Single MDI Command Operation5.5.5Management Frames DatasheetDatasheet Figure 22. MDI State5.5.8Autoscan Operation 5.6.1Features5.6SerDes Interface 5.6.2Functional Description5.6.2.1Transmitter Operational Overview Datasheet5.6.2.5Receiver Jitter Tolerance 5.6.2.4Selective Power-Down5.6.2.3Receiver Operational Overview DatasheetDatasheet 5.6.2.6Transmit Jitter5.6.2.7Receive Jitter Sinusoidal Jitter Mask5.7Optical Module Interface Datasheet5.7.2.1High-SpeedSerial Interface 5.7.2.2Low-SpeedStatus Signaling Interface5.7.2Functional Descriptions 5.7.2.2.1MOD_DEF_0:35.7.2.2.6TX_FAULT_INT 5.7.2.2.2TX_FAULT_0:35.7.2.2.4TX_DISABLE_0:3 5.7.2.2.3RX_LOS_0:35.7.3.2I2C Read Operation 5.7.3I²C Module Configuration Interface5.7.3.1I2C Control and Data Registers •“I2C Control Ports 0 - 3 $0x79B” on page5.7.3.3I2C Write Operation Datasheet5.7.3.6Clock and Data Transitions 5.7.3.4I²C Protocol Specifics5.7.3.5Port Protocol Operation Datasheet5.7.3.6.3Acknowledge 5.7.3.6.1Start Condition5.7.3.6.2Stop Condition Datasheet5.7.3.6.6Random Read Operation 5.7.3.6.4Memory Reset5.7.3.6.5Device Addressing Datasheet5.8.1Modes of Operation 5.8.2LED Interface Signal Description5.8LED Interface Datasheet5.8.3Mode 0: Detailed Operation Datasheet5.8.4Mode 1: Detailed Operation Datasheet5.8.6LED DATA Decodes 5.8.5Power-On,Reset, InitializationDatasheet 5.8.6.1.1 Fiber LED Behavior 5.8.6.1LED Signaling BehaviorDatasheet 5.8.6.1.2Copper LED Behavior 5.9CPU InterfaceDatasheet 5.9.1Functional Description 5.9.1.1Read Access5.9.1.2Write Access Datasheet5.9.1.3CPU Timing Parameters 5.9.2EndianDatasheet 5.10.1TAP State Machine 5.10TAP Interface JTAGDatasheet Datasheet Table 38. Instruction Register Description5.10.4Boundary Scan Register 5.11Loopback Modes5.10.3ID Register 5.10.5Bypass Register5.11.2Line Side Interface Loopback Datasheet5.12.1System Interface Reference Clocks 5.12ClocksDatasheet 5.12.4MDC Clock 5.12.2SPI3 Receive and Transmit Clocks5.12.3RGMII Clocks 5.12.1.1CLK1255.12.7LED Clock 5.12.5JTAG Clock5.12.6I2C Clock Datasheet6.0Applications 6.1Change Port Mode Initialization SequenceDatasheet 13.Assert set to 1 “Port Enable $0x500” Datasheet7.0Electrical Specifications Datasheet7.1DC Specifications DatasheetTable 41. Intel IXF1104 MAC DC Specifications Datasheet7.1.2RGMII Electrical Characteristics 7.1.1Undershoot / Overshoot SpecificationsDatasheet Table 45. RGMII Power Datasheet7.2.1Receive Interface Timing 7.2SPI3 AC Timing SpecificationsDatasheet Datasheet 7.2.2Transmit Interface Timing DatasheetDatasheet 7.3RGMII AC Timing Specification Datasheet7.4.1.11000 BASE-TTransmit Interface 7.4GMII AC Timing Specification7.4.11000 Base-TOperation Datasheet7.4.1.21000BASE-TReceive Interface Datasheet7.5SerDes AC Timing Specification Datasheet7.6.2MDC Low-SpeedOperation Timing 7.6MDIO AC Timing Specification7.6.1MDC High-SpeedOperation Timing DatasheetMDIO 7.6.3MDIO AC TimingDatasheet MDC MDIO7.7.1I2C Interface Timing 7.7Optical Module and I2C AC Timing SpecificationDatasheet Datasheet 7.8.2CPU Interface Write Cycle AC Timing 7.8CPU AC Timing Specification7.8.1CPU Interface Read Cycle AC Timing DatasheetDatasheet 7.9Transmit Pause Control AC Timing Specification Datasheet7.10JTAG AC Timing Specification Datasheet7.11System AC Timing Specification Datasheet7.12LED AC Timing Specification Datasheet8.2Graphical Representation 8.0Register Set8.1Document Structure Datasheet8.4Register Map 8.3Per Port RegistersDatasheet Datasheet Datasheet Datasheet Datasheet Datasheet Datasheet Table 68. SerDes Registers $ 0x780 -Source MAC address bit 8.4.1MAC Control RegistersDatasheet Source MAC address bitTable 73. Collision Distance $ Port_Index + Table 75. FC TX Timer Value $ Port_Index +Datasheet Table 74. Collision Threshold $ Port_Index +Table 78. IPG Receive Time 2 $ Port_Index + 0x0B DatasheetTable 77. IPG Receive Time 1 $ Port_Index + 0x0A Table 79. IPG Transmit Time $ Port_Index + 0x0CTable 80. Pause Threshold $ Port_Index + 0x0E DatasheetTable 81. Max Frame Size Addr: Port_Index + 0x0F Datasheet Table 83. Flush TX $ Port_Index +Datasheet Table 84. FC Enable $ Port_Index +Table 85. FC Back Pressure Length $ Port_Index + Datasheet Datasheet Datasheet Datasheet Datasheet 8.4.2MAC RX Statistics Register Overview DatasheetDatasheet Datasheet Datasheet 8.4.3MAC TX Statistics Register Overview DatasheetDatasheet Datasheet 8.4.4PHY Autoscan Registers DatasheetDatasheet Datasheet Datasheet Datasheet Datasheet Datasheet Table 104. Interface Mode $0x501 Table 103. Port Enable $0x500Datasheet Table 106. MAC Soft Reset $0x505 Table 105. Link LED Enable $0x502Datasheet Table 108. CPU Interface $0x508 Table 107. MDIO Soft Reset $0x506Datasheet Table 109. LED Control $0x509Datasheet Table 111. LED Fault Disable $0x50BTable 110. LED Flash Rate $0x50A Datasheet Table 112. JTAG ID $0x50C8.4.6RX FIFO Register Overview DatasheetTable 117. RX FIFO Low Watermark Port 0 $0x58A DatasheetTable 116. RX FIFO High Watermark Port 3 $0x583 Table 118. RX FIFO Low Watermark Port 1 $0x58BTable 119. RX FIFO Low Watermark Port 2 $0x58C DatasheetTable 120. RX FIFO Low Watermark Port 3 $0x58D Table 122. RX FIFO Port Reset $0x59E DatasheetDatasheet Table 124. RX FIFO Overflow Event $0x5A0Packet Filter Control $ Port_Index + with the“RX FIFO Errored FrameDrop Enable $0x59F” and the “RX 0x19”with the“RX FIFO Errored Frame with the“RX FIFO Errored FrameDrop Enable $0x59F” and the “RX Drop Enable $0x59F” and the “RXDatasheet Datasheet Datasheet High watermark for TX FIFO Port 0. The 8.4.7TX FIFO Register OverviewDatasheet High watermark for TX FIFO Port 1. TheLow watermark for TX FIFO Port 1. The DatasheetLow watermark for TX FIFO Port 0. The Low watermark for TX FIFO Port 2. TheMAC threshold for TX FIFO Port 1. The DatasheetMAC threshold for TX FIFO Port 0. The MAC threshold for TX FIFO Port 2. TheRegister Description: TX FIFO Underflow Event DatasheetRegister Description: TX FIFO Overflow Event Datasheet Table 137. TX FIFO Port Reset $0x620 Sheet 2 of DatasheetDatasheet Table 141. TX FIFO Port Drop Enable $0x63D Datasheet8.4.8MDIO Register Overview DatasheetDatasheet Table 144. Autoscan PHY Address Enable $0x682Table 145. MDIO Control $0x683 SPHY/MPHY Mode 8.4.9SPI3 Register OverviewDatasheet SPHY/MPHY ModeSPHY Mode DatasheetSPHY/MPHY Mode MPHY ModeMPHY Mode DatasheetSPHY Mode SPHY ModeMPHY Mode DatasheetSPHY Mode SPHY ModeMPHY Mode DatasheetSPHY Mode SPHY ModeMPHY Mode DatasheetSPHY Mode SPHY ModeDatasheet 8.4.10SerDes Register Overview DatasheetDatasheet 8.4.11Optical Module Register Overview DatasheetTable 155. I2C Control Ports 0 - 3 $0x79B DatasheetTable 156. I2C Data Ports 0 - 3 $0x79F 9.1Overview 9.0Mechanical Specifications9.1.1Features 9.2Package Specifics for the IXF1104= Ball 9.3Package InformationDatasheet = No ballFigure 56. CBGA Package Side View Diagram DatasheetSyww9001 9.3.1Example Package MarkingDatasheet Pin 1 mark Syww9001 CountryDatasheet 10.0Product Ordering InformationTray