Panasonic Official Manual for the SA VK91D Stereo System
Page 24

The radio

 

 

BAND

 

 

TUNER

, REW/

 

,

/FF

 

PROGRAM

Numbered

PLAY MODE

buttons

 

 

TUNER/AUX

 

operations

 

 

Radio

SKIP

 

 

 

Manual tuning

1Press [TUNER/AUX] (main unit: [BAND, TUNER]) to select “FM” or “AM”.

The unit comes on.

Every time you press the button: FM → AM → AUX

2Press [(] or [)] (main unit: [g, REW/4] or [f, 3/FF]) to select the frequency.

Press and hold [(] or [)] (main unit: [g, REW/4] or [f, 3/FF]) until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found.

“TUNED” is displayed when a radio station is tuned.

“ST” is displayed when a stereo FM broadcast is being received.

LIf noise is excessive in FM

Press [PLAY MODE] to display “MONO”.

Monaural sound is selected and noise reduces when reception is weak.

Press [PLAY MODE] again to cancel the mode. “MONO” is also canceled if the frequency is changed.

LAM allocation setting (main unit only)

For Saudi Arabia, Kuwait, the Middle East, South Africa and Southeast Asia

The step is factory-set to 9 kHz, but you can change it to receive

broadcasts allocated to 10 kHz steps.

1.Select “FM”.

2.Press and hold [BAND, TUNER].

After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed.

To return to the original step, repeat the above steps.

Note

After changing the “allocation” setting, the frequencies you previously

preset in the memory will be cleared. Preset them again.

Preset tuning

There are two methods of pre-setting stations.

Automatic presetting :All the stations the tuner can receive are preset.

Manual presetting :You can select the stations to preset and the order they are preset in.

Up to 15 stations each can be set in the FM and AM bands.

Preparation:

Press [TUNER/AUX] (main unit: [BAND, TUNER]) to select “FM” or “AM”.

Automatic presetting

Do the following once each for FM and AM.

Preparation: Tune to the frequency where pre-setting is to begin.

Press and hold [PROGRAM] until the frequency changes.

The tuner presets all the stations it can receive into the channels in

ascending order.

•“SET OK” is displayed when the stations are set. The last station to be set is then played.

“ERROR” is displayed

Presetting was unsuccessful. Preset manually.

Manual presetting

Pre-set the stations one at a time.

1Tune to the station (A see left).

2Press [PROGRAM].

3While “PGM” is flashing on the display

Press the numbered buttons to select a channel.

Alternatively, press [g, 4] or [f, 3] (main unit:

[g, REW/4] or [f, 3/FF]) then press [PROGRAM].

The station occupying a channel is erased if another station is preset in that channel.

Selecting channels

1Press [TUNER/AUX] (main unit: [BAND, TUNER] to select “FM” or “AM”.

2Press the numbered buttons or [g, 4] or [f, 3] to select the channel.

RQT7700

Page 23 Page 25
Image 24
Page 23 Page 25
Contents SC-VK81D SC-VK71D Example¡ These operating instructions Are applicable to models Instructions are of SC-VK71D for Southeast AsiaMain unit if the controls are the same SystemTable of contents AccessoriesHow to replace the fuse Getting startedThis Plug is not Waterproof Keep DRY Before useDisc information Positioning Speaker connections Twist and pull off the vinyl tip of the speaker cordsBlue Red + Black Gray + Blue Connecting a television with a Video in terminal Connecting a television with Component Video in terminalsConnecting a television with an S Video in terminal Video connectionsRadio and power supply connections Conserving powerAM loop antenna AC in To household AC socketRemote control Quick Setup screen assists you to make necessary settingsSetup DVD/CD Enter Return Shift Do notSetting the time Demo function123 This is a 24-hour clockControl reference guide GettingstartedMain unit Center consoleRemote control Sound EQ, -MANUAL EQ, M.RE-MASTERSound EQ, S.WOOFER Discs Basic play OperationsDisc Frame-by- frame On-screen item selectStarting play from a selected group Main units display Enter numberDiscs Convenient functions Play mode functions Program play up to 24 itemsRepeat play Discs Using navigation menus Using a content screen to find a trackUsing the submenu Using navigation menusPlaying HighMAT discs Playing the programsPlaying a playlist Disc operationsDiscs Using on-screen menus Other SettingsMain Menu Picture Mode Picture Adjustment Transfer ModeSignal type/data Picture MenuDiscs Changing the player’s setting Disc tabVideo tab Changing the delay time Speaker Setting Manual tuning Preset tuningRadio Selecting channelsCassette tapes TapePress , Tape Press , Tape to start playbackSound field and sound quality Dolby Digital and DTSDolby Pro Logic Super SurroundSpeaker level adjustments Using the Manual Equalizer Manual EQUsing the Super Sound Equalizer Multi Re-master Enjoying more natural soundPress and hold Play Mode to select the reverse mode Recording operationsSelect the source to be recorded Press REC on the main unit to start recordingUsing the timers Play/record timerSleep timer TimerEnjoying karaoke Karaoke operationsEnjoying karaoke function Changing the keyAdding an echo effect To record your karaoke performanceConvenient functions Changing the sound range display Other functionsUsing other equipment Using an external unitUsing a subwoofer Optional antenna connectionsTray/disc handling procedure GlossaryReference Opening/closing a disc trayTroubleshooting guide PowerOperation Using the cassette deck SoundPicture Listening to the radioSafety precautions MaintenanceSpecifications Specifications
Top Page Image Contents