IBM DU3 manual Modules

Page 41

	Note: Your Linux operating system may not support SES but the SES
	functions are used when running the standalone AIX Diagnostic CD.
	Attention: The SCSI address of the SCSI attachment that is connected to the
	2104 must be different from the addresses of the installed disk drive modules.
	When a second SCSI attachment is connected to a 2104, the SCSI address of
	that SCSI attachment must be different from the address of the first SCSI
	attachment and different from the addresses of the installed disk drive
	modules.
	12. The 2104 Orientation switch 2 configures the Power and Check lights that
	are on the front of the 2104. Ensure that this switch is set to Off so that the
	lights are correct for your 2104 Model DU3.
	13. The SCSI Bus Split switch 3 controls the SCSI bus configuration of your
	2104. When the switch is set to Off, the 2104 is configured in single SCSI bus
	mode. When the switch is set to On, the 2104 is configured in dual SCSI bus
	(split bus) mode.
	When a 2104 Model DU3 is in dual SCSI bus mode, the SCSI addresses of
	one SCSI bus are 0 through 6, from left to center, and the SCSI addresses of
	the other SCSI bus are 8 through 14, from center to right.
	Refer to the 2104 configuration information, and set the SCSI Bus Split switch
	3 as required.
	14. Switch 4 is reserved. Ensure that is it set to Off.

Installing a 2104 Model DU3 25

Image 41

Contents Model DU3 Installation Guide Page Model DU3 Installation Guide Fourth Edition June Contents Appendix B. Translated Safety Notices Korean Government Ministry of Communication MOC Statement Federal Communications Commission FCC StatementNew Zealand Compliance Statement International Electrotechnical Commission IEC StatementIndustry Canada Compliance Statement Avis de conformité à la réglementation d’Industrie CanadaUnited Kingdom Telecommunications Requirements European Union EU StatementTaiwan Class a Compliance Statement Viii 2104 Model DU3 Installation Guide Safety Notice for Installing, Relocating, or Servicing Definitions of Safety NoticesModel DU3 Installation Guide Electrostatic Discharge ESD Xii 2104 Model DU3 Installation Guide Trademarks Numbering ConventionRelated Publications Xiv 2104 Model DU3 Installation Guide Installing a 2104 Model DU3 Recommended operating temperature is 22C 72F or lower Installing a 2104 Model DU3 into a Rack Refer to Figure Checking the Items for a 2104 Model DU3Preparing the Rack System or Expansion Installing the Support Rails Removing the Disk Drive Modules and Dummy Disk Drive Modules Opening the Handle of a Disk Drive Module Removing a Disk Drive Module Disk Drive Module on its Side for Safe Storage Removing a Dummy Disk Drive Module Installing the 2104 Model DU3 into the Rack Install the two front mounting screws 1 and tighten them Installing the Back Mounting Screws Reinstalling a Disk Drive Module Closing the Handle of a Disk Drive Module Go to Connecting the 2104 Model DU3 to the Power Source on Setting the Box ID Setting the Options on the 2104 Model DU3Now look at the option switches. Refer to Figure Using-system software Unscrew the thumbscrew 1 Opening the Lever on the Switch Card Assembly Pull the switch card assembly out from Scsi Modules Reinstall the switch card assembly a. Refer to Figure Closing the Lever on the Switch Card Assembly Tighten the thumbscrew 1 fully Connecting the Power Plugs Connecting the 2104 Model DU3 to the Power SourceCheck Power Supply Switch and Lights Do not USE a POWER-DRIVEN Screwdriver Connecting the 2104 to the Using System32 2104 Model DU3 Installation Guide Checking the Lights Switching On and Testing34 2104 Model DU3 Installation Guide Configuring a 2104 to the using system Scsi Service AidsIdentifying 2104s and Disk Drive Modules LinuxAppropriate Linux utilities to partition your drives Rmdev -l enclosurenumber -d Unconfiguring a 2104 from the using systemValid 2104 Model DU3 Configurations Summary of Valid 2104 Model DU3 Configurations Single-Bus Mode Configurations To connect to the 2104 Model DU3 or 2104 Model TU3 Type 4-Y, feature Installed 44 2104 Model DU3 Installation Guide Scsi adapter of one of these types For Hacmp configurations in standby or mutual takeover mode Dual-Bus Mode Configurations Valid configuration 1 Operating system Type 4-Y, feature 2104s Dual-Bus Mode Two Adapters in One Using System Connected to One Configurations That are Not ValidInterface Cards. This configuration is not valid 3 56 2104 Model DU3 Installation Guide Using System Subsystem Cluster multiprogramming Hacmp Web Support Pages Collecting Errors60 2104 Model DU3 Installation Guide Related Publications 62 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 64 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 66 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 68 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 70 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 72 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 74 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 76 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 78 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 80 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 82 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 84 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 86 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 88 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 90 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 92 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 94 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices 96 2104 Model DU3 Installation Guide Appendix B. Translated Safety Notices Part Number 97P1455