Panasonic SC-BTT370, BTT273 Following Applies only in the U.S.A. FCC Note, For wireless system

Page 2

THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

Panasonic Corporation of North America

One Panasonic Way

Secaucus, NJ 07094

Support Contact:

Panasonic Consumer Electronics Company

Telephone No.: 1-800-211-PANA (7262)

THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions:

(1)This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

Contains FCC ID: RYYWYPAEBUX4 Contains IC:4389B-WYPAEBUX4

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.

FCC and IC require this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this product.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

[BTT770]

THE FOLLOWING APPLIES ONLY IN THE U.S.A. FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC caution: To maintain compliance with FCC regulations, shielded interface cables must be used with this equipment. Operation with non-approved equipment or unshielded cables may result in interference to radio and TV reception. Any changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

Panasonic Corporation of North America

One Panasonic Way, Secaucus, NJ 07094

Support Contact:

Panasonic Consumer Electronics Company

Telephone No.: 1-800-211-PANA (7262)

WARNING:

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.

To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

[BTT770]

THE FOLLOWING APPLIES ONLY IN CANADA.

This Class B digital apparatus complies with Canadian ICES-003.

[BTT770] [BTT370]

THE FOLLOWING APPLIES ONLY IN CANADA. For main unit

Product Identification Marking is located on the bottom of the unit.

[BTT770]

For wireless system

Product Identification Marking is located on the bottom of wireless system.

VQT3D27

2

Image 2
Contents Model No. SC-BTT770 Illustration shows the image of the unit SC-BTT770Following Applies in the U.S.A. and Canada For wireless systemFollowing Applies only in the U.S.A. FCC Note Following Applies only in CanadaInside of product PlacementUnit Table of contents Accessory 35/Select audio Remote controlTV operation buttons Main unit Front Standby/on switch Power Í/I≥ Automatic power-down function Main unit RearType detail Playable contents Examples Playable discs/CardsUsing the remote control Unit and media carePreparation Preparing the speakersAssembling the speakers Preventing the speakers from falling Speaker cable sticker supplied Connector ColorPreparing cables and making connection  Setup example Wireless systemUpgrade your system to 7.1-channel System PositioningSpeaker cable connection Connection with the wireless system SH-FX71Connections Connection with the main unitConnection for the standard picture and audio Connection to a TV  Connection for the better audioHdmi cable When the Hdmi terminal on the TV is labeled Hdmi ARCWhen the Hdmi terminal on the TV is not labeled Hdmi ARC Optical digital audio cable not suppliedUsing an outdoor antenna When the connecting devices do not have an Hdmi terminalUsing an indoor antenna Connection with Set Top Box, etcConnection to a broadband network Wireless LAN connectionBTT770 Digital transmitter connection LAN cable connectionPress Power C I, B Í on the wireless system AC power supply cord connectionBTT770 Preparing the wireless system Unit on/off button Power C I, B ÍEasy setup assists you to make necessary settings Easy setupPress OK several times to finish the Easy setup PreparationWireless connection Network Easy SettingWired connection Search for wireless networkReprogramming the remote control When you experience problems with settingsInserting or removing media Firmware updatesSelecting the source by the remote control Button SourcePress 3, 4, 2, 1 to select the item Home menuPress Í to turn on the unit Press OKChanging the sound modes Adjusting speaker level during playEnjoying surround sound effects Press Surround several times to select the effectPlaying video contents Enjoying BD-Live discs with Internet Useful functionsEnjoying BD-Live or picture-in-picture in BD-Video Playing picture-in-picture3D settings Enjoying 3D videoPress 3, 4 to select the folder and press OK Playing still picturesTo show the still picture properties Press 3, 4, 2, 1 to select the still picture and press OKPlaying a track in another Presetting stations manuallyPlaying music Listening to the Radio FolderSound modes Enjoying TV with unit’s speakersSurround sound effects Linked operations with Setting the audio linkAutomatic input switching Power on link Speaker controlPower off link Using the iPod/iPhoneEasy control only with Viera remote control IPod/iPhone ConnectionPress 3, 4 to select an item and press OK IPod/iPhone PlaybackEnjoy music/video Basic controlsOther methods of playback EnjoyingEnjoy photos Playback menu Press DisplayAudio PlayVideo Press 3, 4, 2, 1 to select the option and press OK Setup menuDisc Display TV Aspect 3D SettingsTV / Device Connection Hdmi ConnectionNetwork OthersWhen using the 7.1ch speaker system Speaker settingsAdjusting speaker level To avoid speaker dropping Speaker installation optionAttaching to a wall   Drive a screw not supplied into the wallGeneral operation Troubleshooting guidePower DisplaysTV screen and video Sound IPod/iPhone operationMessages Language code list Display languages listReference Specifications BTT770 BTT370 Hdmi AVJpeg File formatFile Extension Reference Panasonic Exchange Center George McVay Drive Suite B Mail-In ServiceLimited Warranty Limits And Exclusions For hearing or speech impaired TTY users, TTYLimited Warranty Only for Canada Panasonic Canada IncIndex LAN