Friedrich SL 24, SS15, SM15, SL 22, YS10 operation manual Through-the-Wall Installation

Page 36

Through-the-Wall Installation

The following instructions apply to wood, masonry, brick, concrete or cinder block wall construction.

STEP 1. Follow steps 1, 2, 3, and 4 of the "STANDARD WINDOW INSTALLATION" instructions beginning on page 25.

STEP 2. CABINET PREPARATION – Remove the sill plate from the cabinet by removing two (4) nuts and screws (Figure 39). Note that the chassis retainer is secured by a right side nut and screw (Detail A, Figure 39). Bend the tabs of the sill plate down into its channel at both ends of the plate or cut them off (Detail B, Figure 39) Rotate the sill plate 180° (end-to-end, Detail B, Figure 39) and reinstall. Reverse the orientation of the nuts and screws, so that the head of the screws are on the underside of cabinet facing up and the nuts are on top (Detail C, Figure 39). Ensure that the chassis retainer is reinstalled as shown in the detail.

NOTICE

The outside cabinet condenser air intake louvers MUST NOT BE BLOCKED by extra thick walls.

STEP 3. WALL PREPARATION – The maximum wall thickness permissible without special construction is determined by the model size to be installed. Observe the maximum wall thickness shown in Figure 40. Walls exceeding the maximum thickness shown in the chart, should be altered as shown in Figure 40.

STEP 4. CHECKING WIRING AND PLUMBING – Check for wiring and plumbing inside and outside of the wall to be sure none will be damaged when the cabinet framework is being constructed.

STEP 5. OPENING CONSTRUCTION – Depending upon size of unit to be installed, lay out the hole dimensions per Table 3. Cut

construction is typical frame or 2” x 4” studding with brick or stone veneers, locate the opening next to one of the studs. For masonry, concrete or cinder block walls, locate opening for your convenience (See Figures 41, 42, and 43).

A

B

Table 3

FINISHED

SMALL

MEDIUM

LARGE

DIMENSION

CHASSIS

CHASSIS

CHASSIS

A

16 3 16"

18 3 16"

20 3 8"

B

26 3 16"

26 3 16"

28 1 4"

size.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Room Air Conditioners Standard Chassis ModelsRegister your air conditioner Table of Contents Safety Precautions Your safety and the safety of others are very importantUnpacking Instructions StepSlide the foam front support forward Carefully lift decorative front box from foam front supportAke sure the wiring is adequate for your unit Test the power cordARN I N G Before Operating Your Unit Do N OT use an extension cordStandard Filter Cleaning / Installation Instructions Premium Carbon Filter Installation Instructions Control Panel Operation Kühl Control Options Auto Mode Cool ModeFAN only Mode Heat ModeContinuous Other FunctionsºF ºC Select DIM FunctionAlerts Lock Control PanelTimer/Schedule Select Timer factory defaultExternal Control Status Advanced FunctionsModify the Timer Function Timer Start Time Timer Stop TimeTimer Scheduler Control Block Schedule on ScenariosTimer on Scenarios Scheduler OFF ScenariosTimer OFF Scenarios Remote Control Operation Remote EffectivenessAuto Auto FAN Continuous Airflow Selection and Adjustment Air flow direction adjustmentRemote Thermostat Fresh air and exhaust controlInstallation Instructions Recommended ToolsRead this FIRST! Electrical Requirements Installation Hardware and Accessory Detail Standard Window Installation Handle UseTOP View of Unit Detail B-2 Slope Down Support Bracket Item Slope Down Stone Ledge Outside Wall Discard Shaded Area Cut/Sever Section A-A Use Tool Provided Location of Grille Removal ToolCord Routing Change Unplug unitCarefully push electrical control panel back into chassis Through-the-Wall Installation Before Caulk ALL Sides Inside and Outside Cabinet Mortar Point Y Trim Moulding Final Inspection & Start-up Checklist Routine Maintenance Service and AssistanceAvailable Accessories Troubleshooting Tips Unit does not operatePage Addendum Schedule Table with Energy Saving ValuesANY Part Sealed Refrigerant System Applicability and Limitations9300100000
Related manuals
Manual 46 pages 14.38 Kb

SM15, SL 24, SS15, SL 22, YS10 specifications

The Friedrich YS10, SL 22, SS15, SL 24, and SM15 are a series of innovative machines designed for various industrial applications, primarily focusing on precision and efficiency in manufacturing processes. Each model boasts unique features tailored to meet distinct needs across different sectors.

The YS10 stands out with its advanced automation capabilities, enabling enhanced productivity through smart technology integration. It employs a state-of-the-art control system that allows operators to program complex tasks with ease, making it suitable for high-volume production environments. Additionally, the YS10 is equipped with an intuitive user interface that simplifies operation and minimizes training time for new users.

Moving on to the SL 22, this model is recognized for its versatility in handling diverse materials. It incorporates adjustable settings that allow users to switch between various manufacturing processes seamlessly. The SL 22 is also designed for energy efficiency, utilizing cutting-edge motion control technology to reduce power consumption without compromising performance. Its robust construction ensures longevity and reliability, essential for demanding industrial applications.

The SS15 is engineered specifically for precision tasks, featuring high-resolution sensors that guarantee exceptional accuracy in measurements. This model excels in environments where tight tolerances are crucial, such as in electronics and automotive manufacturing. The SS15 also includes advanced software for real-time monitoring and adjustments, ensuring consistent results throughout the production cycle.

On the other hand, the SL 24 offers enhanced speed and throughput capabilities, making it ideal for fast-paced industries. Its high-performance motor system delivers rapid cycle times while maintaining stability and control. The SL 24's modular design allows for easy upgrades and expansions, enabling manufacturers to adapt to changing market demands effectively.

Lastly, the SM15 focuses on simplifying maintenance processes, featuring accessible components that minimize downtime during servicing. This model employs predictive maintenance algorithms that analyze performance data, alerting users to potential issues before they lead to failures. The SM15 is designed with user experience in mind, offering a balance of functionality and ease of use.

Together, the Friedrich YS10, SL 22, SS15, SL 24, and SM15 represent a comprehensive lineup of machinery built for modern industrial challenges. With their advanced features, these machines offer companies the tools they need to enhance productivity, ensure precision, and improve overall operational efficiency.
Top Page Image Contents