Friedrich SL 24, SS15, SM15 Routine Maintenance, Service and Assistance, Available Accessories

Page 41

Routine Maintenance

monthly, and more frequently if conditions warrant. The unit must be turned

To Remove, Wash and Replace Filter

Coils & Chassis

NOTE: Do not use a caustic cleaning agent on coils or base pan.. Use a biodegradable cleaning agent and degreaser. The use of harsh cleaning materials may lead to deterioration of the

The indoor coil and outdoor coils and base pan should be inspected periodically (annually or semi-annually) and cleaned of all debris (lint, dirt, leaves, paper, etc.) as necessary. Under extreme conditions, more frequent cleaning may be required. Clean the coils and base pan with a soft brush and compressed air or vacuum. A pressure washer may also be used,

pack when pressure cleaning coils.

NOTE: It is extremely important to insure that none of the electrical and/or electronic parts of the unit get wet. Be sure to cover all electrical components to protect them from water or spray.

Decorative Front

Use a damp (not wet) cloth when cleaning the control area to prevent water from entering the unit, and possibly damaging the electronic control.

The decorative front and the cabinet can be cleaned with warm water and a mild liquid detergent. Do NOT use solvents or hydrocarbon based cleaners such as acetone, naphtha, gasoline, benzene, etc.

The indoor coil can be vacuumed with a dusting attachment if it appears to be dirty. DO NOT BEND FINS. The outdoor coil can be gently sprayed with a hose if you can get to it. If not, you might call your dealer for a more thorough cleaning when needed.

vacuuming with a dust attachment or by cleaning in the sink using warm

reinstalling. Use caution the coil surface can be sharp.

Fan Motor & Compressor

The fan motor & compressor are permanently lubricated, and require no additional lubrication.

Wall Sleeve

Inspect the inside of the wall sleeve and drain system periodically (annually or semi-annually) and clean as required. Under extreme conditions, more frequent cleaning may be necessary. Clean both of these areas with an antibacterial and antifungal cleaner. Rinse both items thoroughly with water and ensure that the drain outlets are operating correctly. Check the sealant around the sleeve and reseal areas as needed.

Service and Assistance

Before calling for service, please check the “Troubleshooting Tips” section

42 43

avoid unnecessary service calls, and save you the cost of a service call if the problem is not due to the product itself. If you have checked the “Basic Troubleshooting” section and still need help, it is available as follows:

our web site at www.friedrich.com.

If you require further assistance

You can call the Customer Support Call Center at 1-800-541-6645.

Before calling, please make sure that you have the complete model and serial number, and date of purchase of your equipment available. By providing us with this information, we will be better able to assist you.

Our specialists are able to assist you with:

Referrals to dealers, and distributors.

Use and Care Information.

Recommended maintenance procedures.

Installation information.

Referrals to Authorized Service Providers and Parts depots.

Available Accessories

DC-2 Drain Kit – Part No. 01900235

In some installations, excess condensate water caused by extremely humid conditions, may result in an undesirable water drip such as on a patio or over an entryway. MODEL DC-2 DRAIN KIT (Part No. 01900-235) can be installed to drain excess condensation to an alternate location.

Carbon Filter Kits

The kits vary depending on the chassis size (small, medium, large). Each

KWCFS KWCFM KWCFL

FriedrichLink™ Adapter Accessory:

KWIFI - FriedrichLink™ Adapter Accessory for wireless control and additional programming options

Decorative Color Front Panel Kits:

The kits vary depending on the chassis size (small, medium, large.)

KWBGE(S/M/L)A- S/M/L Decorative Front Cover in Classic Beige

KWBLK(S/M/L)A - S/M/L Decorative Front Cover in Black Onyx

KWBLU(S/M/L)A - S/M/L Decorative Front Cover in Cobalt Blue

KWPNK(S/M/L)A - S/M/L Decorative Front Cover in Pink Diamond

KWRED(S/M/L)A- S/M/L Decorative Front Cover in Deep Red KWWHT(S/M/L)A- S/M/L Decorative Front Cover in Designer White

Window Installation Kits (Standard in Kühl Models withoutHeat)

KWIKS – For all ES and YS models.

KWIKM – For all EM and YM models.

KWIKL – For all EL and YL models.

See www.friedrich.com for additional accessories for your unit.

41

Image 41
Contents Standard Chassis Models Room Air ConditionersRegister your air conditioner Table of Contents Your safety and the safety of others are very important Safety PrecautionsStep Unpacking InstructionsSlide the foam front support forward Carefully lift decorative front box from foam front supportTest the power cord Ake sure the wiring is adequate for your unitARN I N G Before Operating Your Unit Do N OT use an extension cordStandard Filter Cleaning / Installation Instructions Premium Carbon Filter Installation Instructions Control Panel Operation Kühl Control Options Cool Mode Auto ModeFAN only Mode Heat ModeOther Functions ContinuousDIM Function ºF ºC SelectLock Control Panel AlertsTimer factory default Timer/Schedule SelectExternal Control Status Advanced FunctionsTimer Stop Time Modify the Timer Function Timer Start TimeSchedule on Scenarios Timer Scheduler Control BlockScheduler OFF Scenarios Timer on ScenariosTimer OFF Scenarios Remote Effectiveness Remote Control OperationAuto Auto FAN Continuous Air flow direction adjustment Airflow Selection and AdjustmentRemote Thermostat Fresh air and exhaust controlRead this FIRST! Electrical Requirements Installation InstructionsRecommended Tools Installation Hardware and Accessory Detail Handle Use Standard Window InstallationTOP View of Unit Detail B-2 Slope Down Support Bracket Item Slope Down Stone Ledge Outside Wall Discard Shaded Area Cut/Sever Section A-A Location of Grille Removal Tool Use Tool ProvidedUnplug unit Cord Routing ChangeCarefully push electrical control panel back into chassis Through-the-Wall Installation Before Caulk ALL Sides Inside and Outside Cabinet Mortar Point Y Trim Moulding Final Inspection & Start-up Checklist Available Accessories Routine MaintenanceService and Assistance Unit does not operate Troubleshooting TipsPage Schedule Table with Energy Saving Values AddendumApplicability and Limitations ANY Part Sealed Refrigerant System9300100000
Related manuals
Manual 46 pages 14.38 Kb

SM15, SL 24, SS15, SL 22, YS10 specifications

The Friedrich YS10, SL 22, SS15, SL 24, and SM15 are a series of innovative machines designed for various industrial applications, primarily focusing on precision and efficiency in manufacturing processes. Each model boasts unique features tailored to meet distinct needs across different sectors.

The YS10 stands out with its advanced automation capabilities, enabling enhanced productivity through smart technology integration. It employs a state-of-the-art control system that allows operators to program complex tasks with ease, making it suitable for high-volume production environments. Additionally, the YS10 is equipped with an intuitive user interface that simplifies operation and minimizes training time for new users.

Moving on to the SL 22, this model is recognized for its versatility in handling diverse materials. It incorporates adjustable settings that allow users to switch between various manufacturing processes seamlessly. The SL 22 is also designed for energy efficiency, utilizing cutting-edge motion control technology to reduce power consumption without compromising performance. Its robust construction ensures longevity and reliability, essential for demanding industrial applications.

The SS15 is engineered specifically for precision tasks, featuring high-resolution sensors that guarantee exceptional accuracy in measurements. This model excels in environments where tight tolerances are crucial, such as in electronics and automotive manufacturing. The SS15 also includes advanced software for real-time monitoring and adjustments, ensuring consistent results throughout the production cycle.

On the other hand, the SL 24 offers enhanced speed and throughput capabilities, making it ideal for fast-paced industries. Its high-performance motor system delivers rapid cycle times while maintaining stability and control. The SL 24's modular design allows for easy upgrades and expansions, enabling manufacturers to adapt to changing market demands effectively.

Lastly, the SM15 focuses on simplifying maintenance processes, featuring accessible components that minimize downtime during servicing. This model employs predictive maintenance algorithms that analyze performance data, alerting users to potential issues before they lead to failures. The SM15 is designed with user experience in mind, offering a balance of functionality and ease of use.

Together, the Friedrich YS10, SL 22, SS15, SL 24, and SM15 represent a comprehensive lineup of machinery built for modern industrial challenges. With their advanced features, these machines offer companies the tools they need to enhance productivity, ensure precision, and improve overall operational efficiency.