Friedrich YS10, SS15, SL 24, SM15, SL 22 operation manual Trim Moulding

Page 39

STEP 6. Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the inside wall surface (Figure 21).

STEP 7. Drill three (3) 5/32” diameter pilot holes (use the sill-plate holes as a guide) into the frame and install three (3) #12 x 2" long screws (Item 4) (Figure 21).

NOTE: Alternate fasteners are required when securing the sill plate or support brackets to material other than wood (cinder block, brick, masonry or concrete). These items can be purchased at your local hardware store.

EXPANSION ANCHOR BOLT

MOLLY OR TOGGLE BOLT

NOTE: DO NOT LEVEL the cabinet from front to back. Make sure there is approximately 3/8” to 1/2” slope (1/8 to 1/4 bubble on the level) toward the outside of the house.

STEP 8. Drill two (2) 5/32" diameter pilot holes in each cabinet side at the locations shown (Figure 21) and install four (4) #12 x 2" screws (Item 4). Provided that Step 5 (hole construction) provides a sturdy mount with solid vertical studs, support brackets may not be required. The installation must support the weight of the unit plus an additional weight of 400 pounds on the rear of the cabinet. If support brackets (Item 1) are available, they can be installed as shown in Figure 21.

STEP 9. Complete the installation by following steps 12 through 15 of “STANDARD WINDOW INSTALLATION” instructions, page 25.

Figure 44

TRIM MOULDING

3"

4"

SCREW #12 x 2" LONG (USE 3) (ITEM 4)

SILL PLATE GUIDE CHANNEL

INSIDE WALL SURFACE

CAULK ALL SIDES WEATHER TIGHT

INSIDE AND OUTSIDE

3/8" SLOPE DOWN

NOTE: SUPPORT BRACKET MAY BE

OMITTED FROM THROUGH-THE-WALL

INSTALLATIONS IF THE CABINET IS

SECURED AS FOLLOWS. DRILL TWO

HOLES IN EACH SIDE AND INSTALL 4

FASTENERS (2 EACH SIDE). USE #12 x 2"

SCREWS, (ITEM 4).

TOGGLE BOLTS OR EXPANSION BOLTS

MAY BE REQUIRED.

CABINET

SUPPORT BRACKETS

SCREW #12 x 2" LONG

DRILL 5/32" DIA. PILOT HOLES.

FRR031

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Standard Chassis Models Room Air ConditionersRegister your air conditioner Table of Contents Your safety and the safety of others are very important Safety PrecautionsCarefully lift decorative front box from foam front support Unpacking InstructionsStep Slide the foam front support forwardDo N OT use an extension cord Ake sure the wiring is adequate for your unitTest the power cord ARN I N G Before Operating Your UnitStandard Filter Cleaning / Installation Instructions Premium Carbon Filter Installation Instructions Control Panel Operation Kühl Control Options Heat Mode Auto ModeCool Mode FAN only ModeOther Functions ContinuousDIM Function ºF ºC SelectLock Control Panel AlertsAdvanced Functions Timer/Schedule SelectTimer factory default External Control StatusTimer Stop Time Modify the Timer Function Timer Start TimeSchedule on Scenarios Timer Scheduler Control BlockScheduler OFF Scenarios Timer on ScenariosTimer OFF Scenarios Remote Effectiveness Remote Control OperationAuto Auto FAN Continuous Fresh air and exhaust control Airflow Selection and AdjustmentAir flow direction adjustment Remote ThermostatInstallation Instructions Recommended ToolsRead this FIRST! Electrical Requirements Installation Hardware and Accessory Detail Handle Use Standard Window InstallationTOP View of Unit Detail B-2 Slope Down Support Bracket Item Slope Down Stone Ledge Outside Wall Discard Shaded Area Cut/Sever Section A-A Location of Grille Removal Tool Use Tool ProvidedUnplug unit Cord Routing ChangeCarefully push electrical control panel back into chassis Through-the-Wall Installation Before Caulk ALL Sides Inside and Outside Cabinet Mortar Point Y Trim Moulding Final Inspection & Start-up Checklist Routine Maintenance Service and AssistanceAvailable Accessories Unit does not operate Troubleshooting TipsPage Schedule Table with Energy Saving Values AddendumApplicability and Limitations ANY Part Sealed Refrigerant System9300100000
Related manuals
Manual 46 pages 14.38 Kb

SM15, SL 24, SS15, SL 22, YS10 specifications

The Friedrich YS10, SL 22, SS15, SL 24, and SM15 are a series of innovative machines designed for various industrial applications, primarily focusing on precision and efficiency in manufacturing processes. Each model boasts unique features tailored to meet distinct needs across different sectors.

The YS10 stands out with its advanced automation capabilities, enabling enhanced productivity through smart technology integration. It employs a state-of-the-art control system that allows operators to program complex tasks with ease, making it suitable for high-volume production environments. Additionally, the YS10 is equipped with an intuitive user interface that simplifies operation and minimizes training time for new users.

Moving on to the SL 22, this model is recognized for its versatility in handling diverse materials. It incorporates adjustable settings that allow users to switch between various manufacturing processes seamlessly. The SL 22 is also designed for energy efficiency, utilizing cutting-edge motion control technology to reduce power consumption without compromising performance. Its robust construction ensures longevity and reliability, essential for demanding industrial applications.

The SS15 is engineered specifically for precision tasks, featuring high-resolution sensors that guarantee exceptional accuracy in measurements. This model excels in environments where tight tolerances are crucial, such as in electronics and automotive manufacturing. The SS15 also includes advanced software for real-time monitoring and adjustments, ensuring consistent results throughout the production cycle.

On the other hand, the SL 24 offers enhanced speed and throughput capabilities, making it ideal for fast-paced industries. Its high-performance motor system delivers rapid cycle times while maintaining stability and control. The SL 24's modular design allows for easy upgrades and expansions, enabling manufacturers to adapt to changing market demands effectively.

Lastly, the SM15 focuses on simplifying maintenance processes, featuring accessible components that minimize downtime during servicing. This model employs predictive maintenance algorithms that analyze performance data, alerting users to potential issues before they lead to failures. The SM15 is designed with user experience in mind, offering a balance of functionality and ease of use.

Together, the Friedrich YS10, SL 22, SS15, SL 24, and SM15 represent a comprehensive lineup of machinery built for modern industrial challenges. With their advanced features, these machines offer companies the tools they need to enhance productivity, ensure precision, and improve overall operational efficiency.
Top Page Image Contents