Tool Stickers & Tags, CE Decal CE | Stanley Black & Decker IW12

TOOL STICKERS & TAGS

DANGER

Failure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tools on or near electric lines may result in death or serious injury.

	For proper and safe operation read owners manual
	and mwke sure that you have been properly
ELECTROCUTION	trained in correct procedures required for work
ELECTROCUTION	on or around electric lines.
HAZARD	on or around electric lines.
12412		29083
12412		ROTATION DIRECTION
DANGER DECAL		ROTATION DIRECTION
DANGER DECAL		DECAL
		DECAL

28322	30 LPM @ 138 B AR
28322	EHTMA CATEGORY
CE DECAL (CE)

11207

CIRCUIT TYPE D DECAL (CE)

25610

RAILROAD HELP DESK DECAL

4-12 GPM / 15-45 LPM

DO NOT EXCEED 2000 PSI / 140 BAR

DO NOT EXCEED SPECIFIED FLOW OR PRESSURE USE CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM. CORRECTLY CONNECT HOSES TO TOOL ‘IN’ AND ‘OUT’ PORTS. IMPROPER HANDLING,USE OR OTHER MAINTE-

NANCE OF TOOL COULD RESULT IN A LEAK OR BURST OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS PERSONAL INJURY.

03788

GPM DECAL

28788 Manual Sticker

Lwa

29530

SOUND POWER LEVEL DECAL (CE)

DANGER

		4-12 GPM / 15-45 LPM
	Failure to use hydraulic hose labeled and certied as	DO NOT EXCEED 2000 PSI / 149 BAR
	non-conductive when using hydraulic tools on or near	◘ DO NOT EXCEED SPECIFIED FLOW OR PRESSURE ◘ USE
	electric lines may result in death or serious injury.	CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM. ◘ USE
		OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM. ◘ CORRECTLY
	For proper and safe operation read owners manual	CONNECT HOSE TO TOOL “IN” AND “OUT” PORTS. IMPROPER
	and make sure that you have been properly trained	HANDLING, USE OR MAINTENANCE OF TOOL COULD RESULT
ELECTROCUTION	in correct procedures required for work on or around	IN A LEAK, BURST OR OTHER TOOL FAILURE. ◘ CONTACT AT A
ELECTROCUTION	electric lines.	LEAK OR BURST CAN CAUSE OIL INJECTIONS INTO THE BODY.
HAZARD		◘ FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN
		SERIOUS PERSONAL INJURY.

17275

GPM/PRESSURE DANGER DECAL

NOTE:

		Stanley Hydraulic Tools
		3810 SE Naef Road
		Milwaukie, Oregon USA
	Model No.	15-45 LPM / 4-12 GPM
	IW12	15-45 LPM / 4-12 GPM
	IW12	140 BAR / 2000 PSI

08012

IW12 NAME TAG (US & CE)

THE INFORMATION LISTED ON THE STICKERS SHOWN, MUST BE LEGIBLE AT ALL TIMES.

REPLACE DECALS IF

THEY BECOME WORN OR DAMAGED. REPLACEMENTS ARE AVAILABLE FROM YOUR LOCAL STANLEY DISTRIBUTOR.

The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.

D A N G E R

1.FAILURE TO USE HYDRAULIC HOSE LABELED AND CER- TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

BEFORE USING HOSE LABELED AND CERTIFIED AS NON- CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR- RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPARTMENT INSTRUCTIONS.

2.A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC- TION INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL INJURY.

A.DO NOT EXCEED SPECIFIED FLOW AND PRESSURE FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY CAUSE A LEAK OR BURST.

B.DO NOT EXCEED RATED WORKING PRESSURE OF HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS PRESSURE MAY CAUSE A LEAK OR BURST.

C.CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH YOUR HANDS. CONTACT WITH A LEAK MAY RESULT IN SEVERE PERSONAL INJURY.

I M P O R T A N T

READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

D A N G E R

D.DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR DAMAGED HOSE.

3.MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON- NECTED TO THE TOOL BEFORE PRESSURING SYSTEM. SYSTEM PRESSURE HOSE MUST ALWAYS BE CON- NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT. REVERSING CONNECTIONS MAY CAUSE REVERSE TOOL OPERATION WHICH CAN RESULT IN SEVERE PERSONAL INJURY.

4.DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED- CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.

5.BYSTANDERS MAY BE INJURED IN YOUR WORK AREA. KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.

6.WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO- TECTION.

7.TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINED PERSONNEL.

IM P O R T A N T

READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY STANLEY AND DESCRIBED IN THE OPERATION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

SAFETY TAG P/N 15875 (Shown smaller then actual size)

6 ► IW12 User Manual