Lincoln Electric IM530-C manual Safety Precautions, Routine and Periodic Maintenance

Page 26

MAINTENANCE

SAFETY PRECAUTIONS

WARNING

Have qualified personnel do all maintenance and troubleshooting work.

Turn the engine off before working inside the machine.

Remove guards only when necessary to perform maintenance and replace them when the maintenance requiring their removal is complete.

If guards are missing from the machine, get replacements from a Lincoln Distributor. See the EXPLODED VIEW AND PARTS LIST at the back of this manual.

-------------------------------------------------------------

Read the Safety Precautions in the front of this manual and in the Briggs & Stratton or Robin / Subaru Operating and Maintenance Instructions manual before working on the WELDANPOWER 125.

Keep all equipment safety guards, covers, and devices in position and in good repair. Keep your hands, hair, clothing, and tools away from the recoil housing, fans, and all other moving parts when starting, operating, or repairing this machine.

OIL: Check the oil level after every 5 hours of operation or daily. BE SURE TO MAINTAIN THE OIL LEVEL.

Change the oil the first time after 5 hours of operation for Briggs & Stratton , 20 hours for the Robin / Subaru Then, under normal operating conditions, change the oil after every 50 hours or once a year, whichever occurs first. If the engine is operated under heavy load or in high ambient temperatures, change the oil every 25 hours.

Drain the oil from the drain plug located on either side of the engine bottom, as shown in Figure D.1. Refill through the oil fill plug until the oil reaches the full mark on the dip stick. See Engine Owner’s manual for specific oil recommendations

FIGURE D.1 - OIL DRAIN AND

REFILL LOCATION

Do not screw in

FILL to FULL mark on

dipstick to check oil

dipstick - recheck

ROUTINE AND PERIODIC

MAINTENANCE

ENGINE MAINTENANCE

CAUTION

To prevent the engine from accidentally starting, disconnect the spark plug lead before servicing the engine.

Tighten dipstick firmly before starting

12 mm

HEX

Drain

plug

OIL DRAIN

PLUG

Oil drain

See the Briggs & Stratton or Robin / Subaru Owner’s manual for a summary of maintenance intervals for the engine. Follow either the hourly or the calendar intervals, whichever come first. More frequent service may be required, depending on your specific application and operating conditions. The Briggs & Stratton and Robin / Subaru Owner’s manual shows engine maintenance replacement parts and numbers.

FUEL: At the end of each day’s use, refill the fuel tank to minimize moisture condensation and dirt contamination in the fuel line.

AIR CLEANER: With normal operating

conditions, the maintenance schedule for cleaning and re-oiling the foam pre-filter is every 25 hours and replacement of the air cleaner filter element every 100 hours.

More frequent servicing is required with dusty operating conditions. Refer to the maintenance section of the Engine Owner’s Manual for more information.

WELDANPOWER 125

19

Image 26
Contents Weldanpower Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTable of Contents Amps Location and Ventilation InstallationSafety Precautions StoringTilting PRE-OPERATION Engine ServiceStacking LiftingTotal Combined Length Electrode and Work Cables Electrical Output ConnectionsCable Size and Length Cable Amps Length 30% Duty CycleCable Installation Machine GroundingCircuit Breakers Auxiliary Power ReceptaclesPlugs and Hand Held Equipment Table A.2 Electrical Device USE with the Weldanpower Type Common Electrical Devices Possible ConcernsWeldanpower General Warnings Safety InstructionsOperating Instructions Operation Welding Capability LimitationsControls and Settings Figure B.1 and B.1a Output Panel ControlsStarting/Shutdown Instructions Engine OperationEngine Control Function/Operation Break-in Period To USE the Weldanpower 125 for WeldingWelding Operation Low Oil SensingAfter YOU Finish the Weld Table B.2 Electrode Selection Guide Auxiliary Power OperationTo USE the Weldanpower 125 AS AN Auxiliary Power Supply Table B.3 Auxiliary Power Applications Accessories OPTIONS/ACCESSORIESSafety Precautions Routine and Periodic MaintenanceEngine Maintenance Parts MaintenanceEngine Adjustments Slip RingsTroubleshooting How To Use Troubleshooting GuideTroubleshooting Guide Contact your local Lincoln Authorized Field Service FacilityEngine Problems Welding Problems Wiring Diagram 125Enhanced Diagram Diagram Dimensionprint Weldanpower Weldanpower Precaucion Warnung