Lincoln Electric IM856 manual PRE-OPERATION Service, Battery Connections, Gasoline

Page 10

A-3

INSTALLATION

A-3

 

 

 

3.Proper placement of the equipment on the trailer to insure stability side to side and front to back when being moved and when standing by itself while being operated or serviced.

4.Typical conditions of use, i.e., travel speed; rough- ness of surface on which the trailer will be operated; environmental conditions.

5.Conformance with federal, state and local laws(1)

(1)Consult applicable federal, state and local laws regarding specific requirements for use on public highways.

VEHICLE MOUNTING

WARNING

Improperly mounted concentrated loads may cause unstable vehicle handling and tires or other components to fail.

Only transport this Equipment on serviceable vehicles which are rated and designed for such loads.

Distribute, balance and secure loads so vehicle is stable under conditions of use.

Do not exceed maximum rated loads for compo- nents such as suspension, axles and tires.

Mount equipment base to metal bed or frame of vehicle.

Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------

PRE-OPERATION SERVICE

CAUTION

READ the engine operating and maintenance instructions supplied with this machine.

WARNING

FUEL

Fill the fuel tank with clean, fresh, lead-free gasoline. Observe fuel gauge while filling to prevent overfilling.

WARNING

• Damage to the fuel tank may cause fire or explosion. Do not drill holes in the RANGER GXT base or weld to the RANGER GXT base.

-----------------------------------------------------------------------

OIL

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH20S - 2.0 Quarts (1.9 Liters)

The RANGER GXT is shipped with the engine crankcase filled with SAE 10W-30 oil. Check the oil level before starting the engine. If it is not up to the full mark on the dip stick, add oil as required. Make cer- tain that the oil filler cap is tightened securely. Refer to the engine Owner’s Manual for specific oil recommen- dations.

BATTERY CONNECTIONS

CAUTION

Use caution as the electrolyte is a strong

acid that can burn skin and damage eyes.

-----------------------------------------------------------------------

This welder is shipped with the negative battery cable disconnected. Make sure that the Engine Switch is in the “STOP” position and attach the disconnected cable securely to the negative battery terminal before

GASOLINE

can cause fire or explosion.

Stop engine while fueling.

Do not smoke when fueling.

Keep sparks and flame away from tank.

Do not leave unattended while fueling.

Wipe up spilled fuel and allow fumes to clear before starting engine.

Do not overfill tank, fuel expan- sion may cause overflow.

attempting to operate the machine. If the battery is discharged and does not have enough power to start the engine, see the battery charging instructions in the Battery section.

NOTE: This machine is furnished with a wet charged battery; if unused for several months, the battery may require a booster charge. Be careful to charge the bat- tery with the correct polarity.

GASOLINE FUEL ONLY

------------------------------------------------------------------------

RANGER GXT

Image 10
Contents Ranger GXT Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Height Width Depth Weight InstallationAuxiliary Power Welding OutputSpark Arrester Safety PrecautionsMachine Grounding TowingBattery Connections PRE-OPERATION ServiceGasoline Total Combined Length of Electrode and Work Cables Additional Safety PrecautionsWelding Output Cables Angle of OperationLocation / Ventilation Connection of Lincoln Electric Wire FeedersInstructions StackingDuplex Receptacles Auxiliary Power120/240 Volt Dual Voltage Receptacle Motor StartingElectrical Device USE with the Ranger GXT Type Common Electrical Devices Possible ConcernsSimultaneous Welding and Power Auxiliary Power While WeldingStandby Power Connections Connection of Ranger GXT to Premises Wiring General Description Engine SwitchOperation Welder Controls Function and OperationLocal / Remote Control Switch Polarity Switch PIN ConnectorRanger GXT Approximate Fuel Consumption Starting the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Stopping the EngineStick Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process TIG Constant Current WeldingStick Auto K1745-1 GAS Cylinder Holder AccessoriesK857 25 ft.7.5m or K857-1100 ft.30.4m Stick Wire FeedRecommended Equipment TIGRoutine Maintenance MaintenanceSafety Precautions Engine OIL ChangeAIR Cleaner and Other Maintenance OIL Filter ChangeEngine Adjustments Troubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams PIN Connector M20512 Ranger GXT Precaucion Warnung