Iii

SAFETY

iii

WELDING and CUTTING

SPARKS can

cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire.

Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate cir- cuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During Welding, Cutting and Other Hot Work”, available from NFPA, 1 Batterymarch Park,PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

•Away from areas where they may be struck or subjected to physical damage.

•A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturerʼs recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturerʼs recommendations.

Jan, 07

IM870-A specifications

The Lincoln Electric IM870-A is a cutting-edge industrial robotic welding machine that has garnered attention for its advanced features and capabilities. Designed for high-performance applications, this welding system stands out in the manufacturing environment due to its versatility, precision, and efficiency.

At its core, the IM870-A is equipped with a high-speed manipulator that can handle various welding processes, including MIG, TIG, and flux-cored welding. This flexibility allows manufacturers to adapt the machine for a wide range of materials, including steel, aluminum, and stainless steel. The machine's robust construction ensures durability, making it a reliable choice for demanding industrial applications.

One of the standout features of the IM870-A is its intelligent control system. This system utilizes advanced programming and software to optimize welding parameters in real-time, ensuring consistent weld quality and reducing the likelihood of defects. The machine incorporates Lincoln Electric's proprietary arc control technology, which enhances the stability and reliability of the welding arc, further contributing to improved weld quality.

In addition to its welding capabilities, the IM870-A offers a user-friendly interface that simplifies operation and programming. The machine is designed with intuitive controls, allowing operators to quickly adjust settings and switch between different welding processes. This ease of use is critical in busy production environments, where time and efficiency are of the essence.

Another noteworthy characteristic of the IM870-A is its integration with Industry 4.0 technologies. The machine supports connectivity through IoT (Internet of Things) protocols, enabling remote monitoring and data analysis. This feature allows manufacturers to track performance metrics in real-time, leading to better decision-making and maintenance planning. The analytics provided can identify trends and areas for optimization, ultimately improving overall operational efficiency.

Safety is also a priority in the design of the IM870-A. The machine is equipped with multiple safety features, including automatic shutdown protocols in case of malfunction and protective enclosures to safeguard operators from high-temperature processes.

In summary, the Lincoln Electric IM870-A is a sophisticated welding solution that combines versatility, advanced technology, and user-friendly operation. Its intelligent control systems, Industry 4.0 capabilities, and strong emphasis on safety make it a valuable asset for manufacturers looking to enhance their welding operations and maintain high standards of quality. Whether in automotive assembly, metal fabrication, or other industrial sectors, the IM870-A is an exemplary choice for modern welding needs.