Lincoln Electric SAM400, SAM650 manual Safety

Page 2

i

SAFETY

i

 

 

 

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you pur- chase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame weld- ing arc or when the engine is running. Stop the engine and allow it to cool before refuel- ing to prevent spilled fuel from vaporizing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes

have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V- belts, gears, fans and all other moving parts

when starting, operating or repairing equip- ment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle con- trol rods while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

SAM400 & 650

Page 1 Page 3
Image 2
Page 1 Page 3
Contents IM568 Safety SAM400Electric Shock can kill Welding Sparks can cause fire or explosion Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents HEIGHT1 Width Depth Weight InstallationTechnical Specifications SAM400 Technical Specifications SAM650 Height Width Depth WeightSpark Arrester Installation PrecautionsProduct Description Machine GroundingWelder Location PRE-OPERATION ServiceOutput Cables Operation Operating PrecautionsAdditional Safety Precautions Pipe ThawingPortable Field Control Connection Welder Controls FUNCTION/OPERATIONOutput Studs Mounting on LN-7Contactor Toggle SwitchElectrode Polarity Switch Current and Voltage ControlsTo Set The Controls -- Submerged Arc Variable Voltage WeldingTo Set The Controls -- Stick Welding SAM400 Controls Operation SAM650 Controls Operation Starting Instructions Auxiliary PowerDuty Cycle BREAK-IN PeriodAccessories Periodic Maintenance MaintenanceRoutine Maintenance Bearing MaintenanceCooling System Commutator and Brush MaintenanceContactor Maintenance APR97Troubleshooting HOW to USE Troubleshooting GuideSymptoms Course of Action Function ProblemsLoss of Output in Both Modes of Operation Control Boards. Note a Pg. E-2 Recommended Diode Test Procedure SCR Bridge PC Board Test ProcedureControl PC Board Calibration Ground Tests SAM400 Machine Wiring Diagram LOW Voltage OptionWiring Diagrams SAM650 Machine Wiring DiagramSAM400 Engine Wiring Diagram Maintenance Instructions Daily ChecksSAM650 Engine Wiring Diagram TerminalDimension Print SAM400 and SAM650 Perkins Engine Welders Dimension PrintBasic Course $700.00Precaucion Aviso DE Warranty Repair Statement of Warranty To Obtain Warranty CoverageWarranty Period Warranty Costs

SAM650, SAM400 specifications

Lincoln Electric has long been synonymous with welding excellence, and its SAM series of advanced welding machines, including the SAM400 and SAM650, epitomizes this commitment to quality and innovation. These models are designed to meet the demands of diverse industrial applications while ensuring ease of use, efficiency, and precision.

The SAM400 is a robust multiprocess welding system that supports MIG, TIG, Stick, and Flux-Cored welding techniques. It features a powerful 400 Amp output, suitable for heavy-duty applications and capable of handling materials such as steel, stainless steel, and aluminum. The machine incorporates advanced inverter technology, resulting in a compact design that significantly reduces the weight while enhancing portability. Furthermore, the SAM400 includes intuitive digital controls, allowing operators to easily adjust settings for optimal performance. Its PAS (Power Adapter System) compatibility enables users to seamlessly integrate different power sources, greatly enhancing its versatility.

On the other hand, the SAM650 takes it a step further, boasting a maximum output of 650 Amps. This model is particularly favored in industries requiring high deposition rates, such as shipbuilding and heavy fabrication. Like the SAM400, the SAM650 features multiprocess capabilities but adds enhanced control mechanisms, such as advanced waveform technology, which allows for better arc stability and reduced spatter. This ensures cleaner welds and, ultimately, a superior finish. Additionally, the SAM650 is equipped with Lincoln Electric's proprietary welding technology, including the Arc Control and Hot Start features that enhance user experience by providing smoother starts and consistent performance, even in challenging conditions.

Both machines come with integrated wire feeders that allow for easy adjustments and quick material changes, offering increased productivity on the job site. Their rugged design and durable construction ensure long-lasting performance, even in the harshest environments.

In conclusion, the Lincoln Electric SAM400 and SAM650 welding systems are trailblazers in the field of welding technology. With their powerful output, advanced features, and user-friendly interfaces, these machines cater to the needs of professionals looking for reliability and efficiency in their welding applications. Whether for small shops or large-scale industrial operations, the SAM400 and SAM650 deliver the performance and versatility that fabricators and welders depend on.
Top Page Image Contents