Lincoln Electric C2.410 Flat Fillet Welds, Ft. of Weld/Hr Lbs. of Elec./Ft. 049, 082 117 162 Weld

Page 14

Flat Fillet Welds

Also see Low Hydrogen Procedures.

T

L

Plate Size – T	14 ga		12 ga		10 ga	3/16"	3/16"	1/4"	1/4"
No. of Passes	1		1		1	1	1	1	1
Leg Size – L (in.)	—		—		—	5/32	5/32	3/16	3/16

Electrode/AWS Class				Jetweld 1/E7024-1

Diameter (in.)	3/32	1/8			1/8	1/8	5/32	5/32	3/16

Current (Amps)	95	150			160	180	210	230	270
Polarity	AC		AC		AC	AC	AC	AC	AC
Arc Speed In./Min.(1)	15	17-1/2			17-1/2	17	16-1/2	17	14-1/2
Ft. of Weld/Hr.(2)	75	88			88	85	83	85	72
Lbs. of Elec./Ft. of	.049	.076			.082	.117	.162	.20	.29
Weld

(1)First pass only. On later passes adjust arc speed to obtain proper bead size.

(2)Total for all passes. 100% operating factor.

For X-ray quality:

1.Use low hydrogen procedures, pages 24-34.

(or)

2.Weld 3/16” to 5/16” fillets with E6027 electrodes at the E7024 procedures. Weld 3/8” and larger fillets with 1/4” E6027 at about 400 amps. Travel speed will be slower.

-14-

Image 14

Contents Stick Electrode Welding Guide Page Table of Contents Welding Procedures Out-Of-Position Welding Vertical and OverheadVertical Up Techniques for Fillet and Groove Welds Vertical Up Groove Welds Vertical Down WeldsWeld Vertical Up Fillet Welds160 Polarity High-Deposition Welding Jetweld LH-3800 E7028H8Wrong End view Side view Corner Welds Jetweld 2 E6027 Amps. AC at 14/Min Groove WeldsGroove Welds First Pass Deep Groove Welds Joint a Pass E6011T Over E6011 Root PassesFt. of Weld/Hr Lbs. of Elec./Ft. 049 Flat Fillet WeldsPlate Size T 14 ga 12 ga 10 ga No. of Passes Leg Size L 082 117 162 WeldHorizontal Fillet Welds Welding Inclined Plate 180 Downhill Angle degPolarity Arc Speed In./Min.3 Lbs. of Elec./Ft. High Speed Welding Sheet Metal AlternatePage Edge Welds Fillet Welds Lap WeldsCurrent Amps 120 170 Polarity Diameter PositionCurrent Amps 110 155 Polarity 018 028Burnthrough Spot Welds Roof Decking to Beam Roof Beam Flange Roof Deck Thickness 22 ga 20 ga 18 ga 16 gaLow Hydrogen Welding E7018-1Multipass Page Overhead Groove Welds Diameter Current Amps 155 PolarityArc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. Overhead Fillet Welds Also see Out-of Position Procedures,No. of Pass Leg Size L No. of Passes Leg Size LDiameter Current Amps 230 200 Polarity Horizontal Groove WeldsBack gouge first bead as needed Plate Size T No. of Passes Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. of WeldUse steel backing as on 230 200 PolarityWith E7028 Electrode 132 195 272 409 727 With E7018 Electrode275 350 260 335 157 236 320785 Ft. of Weld/Hr.2 Lbs. of Elec./Ft.203 335 Minimum Preheat and Interpass Temperature1 Stick Electrode Typical Operating Procedures Out-of-Position GroupHigh Deposition Group High Speed GroupLow Hydrogen Group Low Hydrogen, Low Alloy Steel GroupFleetweld Fleetweld 35LS Jetweld Shield-Arc 70+ Fleetweld JetweldFleetweld 5P Shield-Arc Fleetweld 5P+ Shield-Arc HYP+Electric Shock can kill Fumes and Gases can be dangerous For Electrically powered Electric and Magnetic Fields Stick C2.410 12/04