Lincoln Electric C2.410 manual Overhead Groove Welds, Diameter Current Amps 155 Polarity

Page 27

Vertical Up Groove Welds

Also see Out-of-Position Procedures, page 4.

First Pass

3/16" Fleetweld 5P (E6010), 150 amps DC+, 4-1/2 in./min.

Last Pass - back gouge before welding.

T

1/8"

60°

T

1/8"

	Plate Size – T (in.)	1/2	5/8	3/4	1	1-1/4
	No. of Passes	3	4	5	7	9

	Electrode/AWS Class	Jet LH-78MR, Excalibur 7018/E7018
		Excalibur 7018-1/E7018-1

	Diameter (in.)			5/32
	Current (Amps)			155
	Polarity			DC+
	Arc Speed In./Min.(1)			3-1/2
	Ft. of Weld/Hr.(2)	5.4	3.7	2.7	1.6	1.0
	Lbs. of Elec./Ft. of weld	.750(3)	1.21(3)	1.78(3)	3.20(3)	5.05(3)

Overhead Groove Welds

First Pass	1/16"
1/8" Fleetweld 5P (E6010)

110 Amps DC +, 4-1/2 in./min.

Use split weave for all passes after third.

1/16"

T

60°

Plate Size – T (in.)	5/16	3/8	1/2	3/4	1
No. of Passes	1	1	1	1	1

Electrode/AWS Class	Jet LH-78MR,Excalibur 7018 /E7018
	Excalibur 7018-1 /E7018-1

Diameter			5/32”

Current (Amps)	160	160	160	160	160
Polarity	DC+	DC+	DC+	DC+	DC+
Arc Speed In./Min.(1)	3-1/2	3-1/2	3-1/2	4	4
Ft. of Weld/Hr.(2)	10	7.5	5.0	2.5	1.5
Lbs. of Elec./Ft. of weld	.330(4)	.450(4)	.840((4)	1.88(4)	3.34(4)

(1)First low hydrogen pass only. On later passes adjust Arc Speed to obtain proper bead size.

(2)Total for all passes. 100% operating factor.

(3)Plus .280 lbs. of 3/16” E6010/ft. of weld for first pass.

(4)Plus .160 lbs. of 1/8” E6010/ft. of weld for first pass.

-27-

Image 27

Contents Stick Electrode Welding Guide Page Table of Contents Out-Of-Position Welding Vertical and Overhead Welding ProceduresVertical Up Techniques for Fillet and Groove Welds Vertical Down Welds Vertical Up Groove WeldsVertical Up Fillet Welds 160 PolarityWeld Jetweld LH-3800 E7028H8 High-Deposition WeldingWrong End view Side view Corner Welds Groove Welds Groove Welds First PassJetweld 2 E6027 Amps. AC at 14/Min Over E6011 Root Passes Deep Groove Welds Joint a Pass E6011T082 117 162 Weld Flat Fillet WeldsPlate Size T 14 ga 12 ga 10 ga No. of Passes Leg Size L Ft. of Weld/Hr Lbs. of Elec./Ft. 049Horizontal Fillet Welds Welding Inclined Plate Downhill Angle deg Polarity Arc Speed In./Min.3 Lbs. of Elec./Ft.180 Alternate High Speed Welding Sheet MetalPage Edge Welds Lap Welds Fillet Welds018 028 Diameter PositionCurrent Amps 110 155 Polarity Current Amps 120 170 PolarityRoof Deck Thickness 22 ga 20 ga 18 ga 16 ga Burnthrough Spot Welds Roof Decking to Beam Roof Beam FlangeE7018-1 Low Hydrogen WeldingMultipass Page Diameter Current Amps 155 Polarity Overhead Groove WeldsNo. of Passes Leg Size L Overhead Fillet Welds Also see Out-of Position Procedures,No. of Pass Leg Size L Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft.Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. of Weld Horizontal Groove WeldsBack gouge first bead as needed Plate Size T No. of Passes Diameter Current Amps 230 200 Polarity230 200 Polarity Use steel backing as onWith E7028 Electrode With E7018 Electrode 275 350132 195 272 409 727 157 236 320 260 335Ft. of Weld/Hr.2 Lbs. of Elec./Ft. 203 335785 Minimum Preheat and Interpass Temperature1 Out-of-Position Group Stick Electrode Typical Operating ProceduresHigh Speed Group High Deposition GroupLow Hydrogen, Low Alloy Steel Group Low Hydrogen GroupShield-Arc HYP+ Fleetweld JetweldFleetweld 5P Shield-Arc Fleetweld 5P+ Fleetweld Fleetweld 35LS Jetweld Shield-Arc 70+Electric Shock can kill Fumes and Gases can be dangerous For Electrically powered Electric and Magnetic Fields Stick C2.410 12/04