Lincoln Electric C2.410 manual Ft. of Weld/Hr.2 Lbs. of Elec./Ft, 203 335, 785

Page 34

-34-

With E7018 Electrode

	No. of Passes	1	1	1	1	2	3	4	5
	Leg Size – L (in.)	5/32	3/16	1/4	5/16	3/8	1/2	5/8	3/4

	Electrode/AWS Class	Jet LH-78MR, Jetweld LH-70, Excalibur 7018, Excalibur 7018-1

	Diameter (in.)	3/16	7/32	7/32	1/4	1/4	1/4	1/4	1/4

	Current (Amps)	240	275	275	350	350	350	350	350
	Polarity	AC	AC	AC	AC	AC	AC	AC	AC
	Arc Speed In./Min.(1)	13	11.5	9	7	9	10	8	7.5
	Ft. of Weld/Hr.(2)	65	58	45	35	26	17	11	7.5
	Lbs. of Elec./Ft. of	.111	.140	.203	.335	.480	.785	1.18	1.62

(1)First pass only. On later passes, adjust arc speed to obtain proper bead size.

(2)Total for all passes. 100% operating factor.

Note: E7018 can produce code quality welds. E7018 procedures are used when E7028 is not available and for electrodes E8018 and E11018.

L

L

Horizontal Fillet Welds

Image 34

Contents Stick Electrode Welding Guide Page Table of Contents Welding Procedures Out-Of-Position Welding Vertical and OverheadVertical Up Techniques for Fillet and Groove Welds Vertical Up Groove Welds Vertical Down Welds160 Polarity Vertical Up Fillet WeldsWeld High-Deposition Welding Jetweld LH-3800 E7028H8Wrong End view Side view Corner Welds Groove Welds First Pass Groove WeldsJetweld 2 E6027 Amps. AC at 14/Min Deep Groove Welds Joint a Pass E6011T Over E6011 Root PassesFt. of Weld/Hr Lbs. of Elec./Ft. 049 Flat Fillet WeldsPlate Size T 14 ga 12 ga 10 ga No. of Passes Leg Size L 082 117 162 WeldHorizontal Fillet Welds Welding Inclined Plate Polarity Arc Speed In./Min.3 Lbs. of Elec./Ft. Downhill Angle deg180 High Speed Welding Sheet Metal AlternatePage Edge Welds Fillet Welds Lap WeldsCurrent Amps 120 170 Polarity Diameter PositionCurrent Amps 110 155 Polarity 018 028Burnthrough Spot Welds Roof Decking to Beam Roof Beam Flange Roof Deck Thickness 22 ga 20 ga 18 ga 16 gaLow Hydrogen Welding E7018-1Multipass Page Overhead Groove Welds Diameter Current Amps 155 PolarityArc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. Overhead Fillet Welds Also see Out-of Position Procedures,No. of Pass Leg Size L No. of Passes Leg Size LDiameter Current Amps 230 200 Polarity Horizontal Groove WeldsBack gouge first bead as needed Plate Size T No. of Passes Arc Speed In./Min Ft. of Weld/Hr Lbs. of Elec./Ft. of WeldUse steel backing as on 230 200 PolarityWith E7028 Electrode 275 350 With E7018 Electrode132 195 272 409 727 260 335 157 236 320203 335 Ft. of Weld/Hr.2 Lbs. of Elec./Ft.785 Minimum Preheat and Interpass Temperature1 Stick Electrode Typical Operating Procedures Out-of-Position GroupHigh Deposition Group High Speed GroupLow Hydrogen Group Low Hydrogen, Low Alloy Steel GroupFleetweld Fleetweld 35LS Jetweld Shield-Arc 70+ Fleetweld JetweldFleetweld 5P Shield-Arc Fleetweld 5P+ Shield-Arc HYP+Electric Shock can kill Fumes and Gases can be dangerous For Electrically powered Electric and Magnetic Fields Stick C2.410 12/04