Friedrich SQ05, SQ10 Make sure the wiring is adequate for your unit, Do not use an extension cord

Page 6

WARNING: Before Operating Your Unit

Make sure the wiring is adequate for your unit.

If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in Table 1.

DO NOT use an extension cord.

The cord provided will carry the proper amount of electrical power to the unit; an extension cord may not.

Make sure that the receptacle is compatible with the air conditioner cord plug provided.

This insures proper grounding. If you have a two prong receptacle you

electrician. The grounded receptacle should meet all national and local codes and ordinances. Under no circumstances should you remove the ground prong from the plug. You must use the three prong plug furnished with the air conditioner.

Test the power cord

All Friedrich room air conditioners are shipped from the factory with a Leakage Current Detection Interrupter (LCDI) equipped power cord. The LCDI device meets the UL and NEC requirements for cord connected air conditioners effective August 2004.

To test your power supply cord:

1.Plug power supply cord into a grounded 3 prong outlet.

2.Press RESET (See Figure 1).

3. Press TEST, listen for click; the RESET button trips and pops out.

4.Press and release RESET (Listen for click; RESET button latches and remains in). The power cord is ready for use.

Once plugged in, the unit will operate normally without the need to reset the LCDI device.

If the LCDI device fails to trip when tested or if the power supply cord is damaged, it must be replaced with a new power supply cord from the manufacturer. Contact our Technical Assistance Line at (800) 541-6645. To expedite service, please have your model number available.

NOTICE

Do not use the LCDI device as an ON/OFF switch.

Failure to adhere to this precaution may cause premature equipment malfunction.

Table 1.

 

 

CIRCUIT RATING

REQUIRED WALL

 

 

OR TIME DELAY

 

 

RECEPTACLE

 

MODEL

FUSE

 

 

 

 

 

 

 

AMP

VOLT

NEMA NO.

 

 

 

 

 

 

 

 

 

 

 

SQ05

‡ SQ06

 

 

 

 

 

 

SQ08

‡ SQ10

15

125

5-15P

 

 

 

 

 

 

EQ08

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

Electrical Shock Hazard

Make sure your electrical receptacle has the same configuration as your air conditioner’s plug. If different, consult a Licensed Electrician.

Do not use plug adapters.

Do not use an extension cord.

Do not remove ground prong.

Always plug into a grounded 3 prong oulet.

Failure to follow these instructions can result in death, fire, or electrical shock.

Figure 1

RESET

TEST

WARNING:

TEST BEFORE EACH USE!

1.PRESS REST BUTTON.

2.PLUG LCDI INTO POWER RECEPTACLE.

3.PRESS TEST BUTTON, RESET BUTTON SHOULD POP UP.

4.PRESS RESET BUTTON FOR USE.

DO NOT USE IF ABOVE TEST

FAILS.

WHEN GREEN LIGHT IS ON.

IT IS WORKING

PROPERLY!

FRR072

6

Image 6
Contents RoomAirConditioners Register your air conditioner Table of Contents Safety Precautions Your safety and the safety of others are very importantUnpacking Instructions Make sure the wiring is adequate for your unit Test the power cordDo not use an extension cord Standard Filter Cleaning / Installation Instructions Premium Carbon Filter Installation InstructionsFAN only FAN Mode Control Panel OperationKühl Control Options See FigureAuto FAN No Cooling Demand Control Panel Operation InstructionsRIRSHUDWLRQ Auto FAN Cooling DemandTimer Schedule PointIcon illuminates ºF ºC Select DIM FunctionAlerts Lock Control Panel7KHFRQWUROV\VWHPKDVWKUHH7LPHU6FKHGXOHIXQFWLRQV Timer/Schedule SelectExternal Control Status Programming section of this manualModify the Timer Function Timer Start Time Display returns to normal once the settings are savedTimer Stop Time Schedule on Scenarios Timer Scheduler Control Block$OOEXWWRQDFWLRQLVEORFNHG Display shows a normal systemTimer on Scenarios Display shows the unit in Schedule modeScheduler OFF Scenarios Timer OFF Scenarios Timer icon turns off. The display shows a normal systemState Remote Control Operation Power Button Turns remote and unit on and offRemote Effectiveness FAN Auto FAN Mode Continuous Installation Instructions Read this FIRST! Electrical RequirementsDLUÀRZSRVLWLRQLQJ Recommended tools required for installation not included Item no Description QTYStandard Window Installation ZLQGRZVWRRODVVKRZQLQLJXUH6HFWLRQ$$Cut/Sever If chassis seal gasket is not installed, the operation EwrcsExcessive Weight Hazard Cord Routing Change Unplug unitFactory Setting with LEFT-SIDE Place the cabinet in the framed opening Thru-the-wall InstallationHpryh the shell channel from the top of the cabinet See , CabinetSolid Masonry Construction Condensation is normal Final Inspection & Start-up ChecklistThis is a warm weather appliance FrostingRoutine Maintenance Service and AssistanceAvailable Accessories Troubleshooting Tips \FOHV2Q$QG2II7RRUHTXHQWO\VLHGXQLW 8QLW5XQV7RR0XFKSODWHDUHERWKDJHQF\FHUWL¿HG Addendum Schedule Table with Energy Saving ValuesRoom AIR Conditioners Limited Warranty 9300100100
Related manuals
Manual 108 pages 3.28 Kb

SQ08, SQ05, SQ06, SQ10 specifications

Friedrich is a renowned name in the HVAC industry, known for its innovative solutions in cooling and heating technologies. Among its impressive lineup, the SQ series, consisting of models SQ10, SQ06, SQ05, and SQ08, stands out for their robust features and advanced performance.

One of the defining characteristics of the SQ series is its energy efficiency. Each model is designed to optimize energy use, allowing for significant cost savings while reducing the environmental impact. This is primarily achieved through the incorporation of advanced inverter technology, which adjusts the compressor speed according to cooling or heating demand, maintaining a comfortable indoor climate without excessive energy consumption.

The SQ series units are equipped with high-performing compressors that provide rapid cooling and heating capabilities. This means that users can expect fast temperature adjustments, ensuring a comfortable environment even during extreme weather conditions. Moreover, the noise levels of these units have been engineered to remain low, offering whisper-quiet operation that does not disrupt daily activities.

Control and convenience are also paramount in the SQ series. The units feature smart technologies that allow for remote operation through mobile applications. This means homeowners can adjust temperatures, set schedules, and monitor their energy usage from anywhere, adding a layer of convenience to the user experience. The user-friendly interface and intuitive controls further enhance accessibility.

Durability and reliability are core elements of the SQ models. Constructed with high-quality materials and components, these units are built to withstand the rigors of daily use. The units also come with comprehensive warranties, offering peace of mind to users regarding long-term performance.

In summary, Friedrich's SQ10, SQ06, SQ05, and SQ08 units showcase a blend of energy efficiency, advanced technology, and user-centric features. With their quiet operation, fast temperature adjustments, and smart connectivity, they provide an ideal solution for reliable heating and cooling needs in residential or commercial spaces. The robust design ensures longevity, making Friedrich a trusted choice in climate control solutions.