
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ AND UNDERSTAND ALL INSTRUCTIONS. When using electric appliances, basic precautions should always be followed, including the following:
Before using the work light, read this operator's manual, your battery pack and charger operator's manual, and all labels on the battery pack, charger and work light.
• Read all the instructions before using the | objects that can make a connection from one | |
appliance. | terminal to another. Shorting the battery termi- | |
• To reduce the risk of injury, close supervision | nals together may cause sparks, burns, or a fire. | |
is necessary when an appliance is used near | • Never insert bulbs other than MILWAUKEE | |
children. | bulbs in the bulb socket. Bulbs other than | |
• Do not use outdoors. | MILWAUKEE bulbs may cause short circuit of | |
• For a rechargeable appliance - Use only the char- | battery and personal injury. | |
• Warning - The lens gets very hot during use. To | ||
ger supplied by the manufacturer to recharge. | ||
| reduce the risk of burns, do not touch hot lens. |
WARNING To reduce the risk of injury, do not look directly into the light when the work light is on.
Adjusting the Pivot Head
Cat. No.
Cat. No.
For work light
For work light
On Cat. No.
See your nearest MILWAUKEE Retailer or Service Center to obtain replacement bulbs.
WARNING To reduce the risk of injury and damage, never insert bulbs other than the recommended MILWAUKEE replacement bulb in the bulb socket. Other bulbs will over heat!
• For an appliance with a replaceable lamp - |
| • Store idle work light out of reach of children. | ||||||
always unplug or remove battery pack before |
| |||||||
replacing the lamp. See "Specifications" for |
| Warm work lights can become hazardous in the | ||||||
replacement bulbs. |
|
|
| hands of children. | ||||
• Know your work light. Read this manual care- |
| • Maintain labels and nameplates. These carry | ||||||
fully to learn your work light's applications and |
| important information. If unreadable or missing, | ||||||
limitations as well as potential hazards associ- |
| contact a MILWAUKEE service facility for a free | ||||||
ated with this type of tool. |
| replacement. | ||||||
• Batteries must be recharged only with the |
| SAVE THESE | ||||||
charger specified by the manufacturer. A char- |
| |||||||
ger that may be suitable for one type of battery |
| INSTRUCTIONS | ||||||
may create a risk of fire when used with another |
| |||||||
battery. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Symbology |
| |
• Use work light only with specifically desig- |
|
|
| |||||
|
|
| ||||||
nated battery pack. Use of any other batteries |
|
|
|
| ||||
|
| Direct Current |
| |||||
may create a risk of fire. |
|
|
|
|
| |||
• When battery pack is not in use, keep it away |
|
|
|
| ||||
|
|
|
| |||||
from metal objects like: paper clips, coins, |
|
| Underwriters Laboratories, Inc. |
| ||||
keys, nails, screws, or other small metal |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| Specifications |
| ||||
|
|
|
|
|
|
|
|
|
Cat. No. | Volts DC |
| Replacement Bulbs |
|
| For use with Battery Packs: |
| |
18 |
|
|
| |||||
12 |
|
|
|
|
Fig. 1
WARNING To reduce the risk of injury, DO NOT operate work light without bezel assembly in place. Bulb does get hot. Always remove battery pack before changing or removing bulbs. Always allow the work light to cool for at least 10 minutes before replacing the bulb.
Replacing the Bulb
1.Remove battery pack before changing bulb.
2.Unscrew the bezel assembly on pivot head by turning counterclockwise.
3.Remove the bezel assembly.
4.For Cat. No.
OPERATION
To turn on the work light, press the ON/OFF but- ton. To turn off the work light, press the ON/OFF button again.
Hook (Cat. No.
To use the hanging hook, press in the hook joint. Pull the hook out.
Fig. 3
Press | Pull out |
ACCESSORIES
FUNCTIONAL DESCRIPTION
1. | Bezel assembly | 1 | 5 |
2. | On/Off button |
| |
3. | Magnet |
| 3 |
4. | Hook | 5 | |
5. | Pivot head |
| |
|
| ||
|
|
| 2 |
|
|
| 4 |
1 | 2 |
|
|
ASSEMBLY
WARNING Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into the body of the tool. Insert the battery pack until the battery latches lock.
To remove the battery pack, press in both battery latches and slide the battery pack off of the tool.
Fig. 2 Cat. No. 49-24-0171 
Aluminum heat sink 
Bulb |
Pull forward |
5.Gently rotate the bulb counter clockwise and pull out.
To install new bulb, follow above directions in reverse.
NOTE: Use a soft cloth when installing bulbs. Direct contact with oils or other contamination can shorten the life of bulbs.
WARNING Always remove battery pack before changing or removing accessories. Only use accessories specifi- cally recommended for this tool. Others may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go online to www.milwaukeetool.com. To obtain a catalog, con- tact your local distributor or a service center listed on the back cover of this operator’s manual.
2 | 3 |