General Machinery Cautions
-Misuse of this machine can cause serious injury.
-For safety, the machine must be set up, used and serviced properly.
-Read, understand and follow the instructions in the operator’s and parts manual which was shipped with your machine.
When setting up the machine:
-Always avoid using the machine in damp or poorly lighted work areas.
-Always be sure the machine is securely anchored to the floor.
-Always keep the machine guards in place.
-Always put the start switch in the “OFF” position before plugging in the machine.
When using the machine:
-Never operate the machine with safety guards missing.
-Always wear safety glasses with side shields (See ANSI Z87.1)
-Never wear loose clothing or jewelry.
-Never overreach — you may slip and fall into the machine.
-Never leave the machine running while unattended.
-Always shut the machine off when not in use.
When servicing the machine:
-Always unplug the machine from the electrical power while servicing.
-Always follow the instructions in the operators and parts manual when changing accessory tools or parts.
-Never modify the machine without consulting Wilton Corporation.
You — the stationary power tool user — hold the key to safety.
Read and follow these simple rules for best results and full benefits from your machine. Used properly, Wilton’s machinery is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use them correctly. They should read and understand the Operators and Parts Manual as well as all labels affixed to the machine. Failure in following all of these warnings can cause serious injuries.
6
General Machinery Warnings
1.Always wear protective eye wear when operating ma- chinery. Eye wear shall be impact resistant, protective safety glasses with side shields which comply with ANSI Z87.1 specifications. Use of eye wear which does not comply with ANSI Z87.1 specifications could result in severe injury from the breakage of the eye protection.
2.Wear proper apparel. No loose clothing or jewelry which can get caught in moving parts. Rubber soled, nonslip, footwear is recommended for best footing.
3.Do not overreach. Failure to maintain a proper working position can cause you to fall into the machine or cause your clothing to get caught — pulling you into the machine.
4.Keep the guards in place and in proper working order. Do not operate the machine with the guards removed.
5.Avoid dangerous working environments. Do not use sta- tionary machine tools in wet or damp locations. Keep work areas clean and well lit.
6.Special electrical precautions should be taken when working on flammable materials.
7.Avoid accidental starts by being sure that the start switch is in the “OFF” position before plugging in the machine.
8.Never leave the machine running while unattended. The machine shall be shut off whenever it is not being used.
9.Disconnect the electrical power before servicing, when- ever changing accessories or when general maintenance is done on the machine.
10.Maintain all machine tools with care. Follow all mainte- nance instructions for lubricating and the changing of ac- cessories. No attempt shall be made to modify or have makeshift repairs done to the machine. This not only voids the warranty but also renders the machine unsafe.
10.The machinery must be anchored to the floor.
11.Secure your work. Use clamps or a vise to hold your work, when practical. It is safer than using your hands and it frees both hands to operate the machine.
12.Never brush chips away while the machine is in opera- tion.
13.Keep work area clean. Cluttered areas invite accidents.
14.Remove adjusting keys and wrenches before turning the machine on.
15.Use the right tool. Don’t force a tool or attachment to do a job it was not designed for.
16.Use only recommended accessories and follow manu- facturers instructions pertaining to them.
17.Keep hands in sight and clear of all moving parts and cutting surfaces.
18.All visitors should be kept at a safe distance from the work area. Make your workshop completely safe by using padlocks, master switches, or by removing starter keys.
19.Know the tool you are using — its application, limita- tions, and potential hazards.