OPERATION |
WELDING PROCESS
For any electrodes the procedures should be kept within the rating of the machine. For electrode infor- mation see the appropriate Lincoln publication.
STICK (CONSTANT CURRENT) WELDING
Connect welding cables to the "TO WORK” and "ELECTRODE” studs. Start the engine. Set the "Polarity” switch to the desired polarity. The “RANGE” switch markings indicate the maximum current for that range as well as the typical electrode size for that range. The “OUTPUT” Control provides fine adjust- ment of the welding current within the select range. For maximum output within a selected range set the “OUTPUT” Control at 10. For minimum output within a selected range set the “OUTPUT” Control at 5. (“OUT- PUT” Control settings below 5 may reduce arc stabili- ty) For best overall welding performance set the “RANGE” Switch to the lowest setting and the OUT- PUT” Control near the maximum to achieve the desired welding current.
RANGE SETTING | TYPICAL | CURRENT RANGE |
| ELECTRODE SIZE |
|
|
|
|
90 MAX. | 3/32 | 40 TO 90 AMPS |
|
|
|
145 MAX. | 1/8 | 70 TO 145 AMPS |
|
|
|
210(DC)/225(AC) | 5/32 | 120 TO 210(DC), |
|
| 225(AC) AMPS |
|
|
|
The RANGER® 225 GXT can be used with a broad range of AC and DC stick electrodes. See “Welding Tips 1” included with the RANGER® 225 GXT for electrodes within the rating of this unit and recom- mended welding currents of each.
TIG (CONSTANT CURRENT) WELDING
The RANGER® 225 GXT can be used in a wide variety of AC and DC Tungsten Inert Gas (TIG) welding applications for AC TIG Welding up to 200 amps and DC TIG welding up to 210 amps.
The K930 [ ] TIG Module installed on a RANGER® 225 GXT provides high frequency and shielding gas control for AC and DC GTAW (TIG) welding processes. The TIG Module allows full range output control.
When using the RANGER® 225 GXT for AC TIG welding of alu- minum the following settings and electrodes are recommended:
SETTINGS FOR PURE TUNGSTEN
TUNGSTEN | RANGE SWITCH | APPROXIMATE | |||
DIAMETER (in.) | SETTINGS | CURRENT RANGE | |||
|
|
| |||
1/8 | 80 or 130 | 100 - 300 Amps | |||
3/32 | 80 | 45 | - | 140 | Amps |
1/16 | 80 | 45 | - | 100 | Amps |
|
|
|
|
|
|
SETTINGS FOR 1% THORIATED TUNGSTEN
TUNGSTEN | RANGE SWITCH | APPROXIMATE | |||
DIAMETER (in.) | SETTINGS | CURRENT RANGE | |||
|
|
|
|
|
|
1/8 | 80, 130, or 180 | 80 | - | 225 | Amps |
3/32 | 80 or 130 | 50 | - | 180 | Amps |
1/16 | 80 | 45 - 120 Amps | |||
|
|
|
|
|
|
For AC TIG Welding, the maximum TIG Welding out- put currents on each range setting will be approxi- mately 50% higher than those marked on the name- plate. This is due to the special nature of the AC TIG welding arc. Do not AC TIG weld on the 210DC/225AC Amp setting. The output may exceed the rating of the RANGER® 225 GXT.
WIRE FEED WELDING PROCESSES (CONSTANT VOLTAGE)
The Innershield® electrode recommended for use with the RANGER® 225 GXT is
Diameter | Wire Speed | Approximate | |
(in.) | Range In./Min. | Current Range | |
|
|
|
|
.035 | 80 | - 110 | 75A to 120A |
.045 | 70 | - 130 | 120A to 170A |
.068 | 40 | - 90 | 125A to 210A |
|
|
|
|
The RANGER® 225 GXT is recommended for limited “MIG” welding (GMAW - gas metal arc welding). The recommended electrodes are .030” and .035”
225 GXT are shown in the following table:
Diameter | Wire Speed | Approximate | |
(in.) | Range In./Min. | Current Range | |
|
|
|
|
.030 | 75 | - 300 | 50A to 130A |
.035 | 100 | - 250 | 90A to 175A |
|
|
|
|
ARC GOUGING
The RANGER® 225 GXT can be used for limited arc gouging.
Set the Range switch to adjust output current to the desired level for the gouging electrode being used according to the ratings in the following table:
ELECTRODE SETTING | CURRENT RANGE (DC, electrode positive) | ||
|
|
|
|
1/8 | 30 | - | 60 Amps |
5/32 | 90 | - | 150 Amps |
3/16 | 150 - 250 Amps | ||
|
|
|
|
RANGER® 225 GXT