Lincoln Electric 11572 manual 5INSTALLATIONA-5, BATTERY ChARGING, To prevent ExPLOSION when

Page 12

A-5INSTALLATIONA-5

bATTERY ChARGING

WARNING

GASES FROM bATTERY can explode.

• Keep sparks, flame and cigarettes away.

bATTERY ACID can burn eyes and

skin.

• Wear gloves and eye protection and

be careful when boosting, charging or working near battery.

To prevent ExPLOSION when:

a)Installing a new battery - disconnect thenega- tive cable from the old battery first and connect the negative cable to the new battery last.

b)Connecting a battery charger - remove the bat- tery from the welder by disconnecting the nega- tive cable first, then the positive cable and bat- tery clamp. When reinstalling, connect the neg- ative cable last.

c)using a booster - connect the positive lead to the battery first, then connect the negative lead to the ground lead on the base.

To prevent ELECTRICAL DAMAGE when:

a)Installing a new battery.

b)using a booster.

use correct polarity - Negative Ground.

To prevent bATTERY DISChARGE, if you have an ignition switch, turn it off when engine is not r u n - ning.

•To prevent bATTERY buCKLING, tighten nuts on battery clamp until snug.

------------------------------------------------------------------------

The Classic® 300D Perkins is equipped with a wet charged battery. The charging current is automatical- ly regulated when the battery is low (after starting the engine) to a trickle current when the battery is fully charged.

When replacing, jumping or otherwise connecting the battery to the battery cables, the proper polarity must be observed. This system is NEGATIVE GROuND.

CLASSIC® 300D PERKINS

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Classic 300 D Perkins Safety California Proposition 65 WarningsElectric ShOCK can kill ARC Rays can burnFuMES and Gases can be dangerous Welding and CuTTING Sparks can Cause fire or explosion Cylinder may explode if damagedIii PRÉCAuTIONS DE Sûreté Sûreté Pour Soudage a L’ArcPlease Examine Carton and Equipment For Damage Immediately On-Line Product RegistrationTAbLE of Contents Installation TEChNICAL Specifications Classic 300D PerkinsDesign FEATuRES Rated OuTPuT DuTY CycleControl Panel DuPLEx Receptacle and Gfci MODuLETrailer see Optional FEATuRES MAChINE GROuNDINGLift bAIL VEhICLE MOuNTING Polarity Control and CAbLE SIzESFuEL 5INSTALLATIONA-5 BATTERY ChARGINGTo prevent ExPLOSION when To prevent Electrical Damage whenOperation Starting ThE Classic 300D Perkins 404D-22 Diesel EngineCold WEAThER Starting Stopping ThE EngineWelder Operation Engine bREAK-INIdler Operation Accessories Optional FEATuRES Field InstalledWire Feed Module K623-1 Magnum 250 Innershield Gun for LN-23P K355-10Gun tube for PipeWelding KP1909-1 Maintenance Safety PRECAuTIONSGeneral INSTRuCTIONS BEARINGSPuRGING AIR from FuEL System Perkins 404D-22 Engine Vent Screw Priming LeverMaintenance Gfci MODuLE Testing and Resetting PROCEDuRE TROubLEShOOTING HOW to uSE TROubLEShOOTING GuIDEPRObLEMS POSSIbLE CAuSECOuRSE of Action Electronic Idler TROubLEShOOTING GuIDE Open ClosedAuxiliary Power Load is Turned on Defective -- Will Not CloseAuthorized Field Service Facility Contact your local LincolnWater passage. Flush the system Ing on Faulty light wiring Diagrams Enhanced DiagramDiagrams 24.00 40.94 37.12 Skid18.50 23.00Classic 300D Perkins Classic 300D Perkins Atenção Atenção

11572 specifications

Lincoln Electric 11572 is a high-performance welding machine that has garnered attention in the industry for its reliability and innovative technologies. Primarily designed for MIG welding, this unit stands out due to its combination of portability, ease of use, and superior welding capabilities. It caters to both professional welders and DIY enthusiasts, making it a versatile option for a variety of welding tasks.

One of the key features of the Lincoln Electric 11572 is its compact design. Weighing in at just over 30 pounds, it is lightweight enough for easy transportation, allowing users to take it to job sites or different workshop locations without hassle. Despite its portable nature, it does not compromise on performance, providing a robust output that is capable of handling a range of materials, including mild steel, stainless steel, and aluminum.

The machine is equipped with a variable voltage control, which allows users to adjust the output to suit different welding thicknesses and types. This flexibility aids in achieving optimal welds, ensuring a good balance between penetration and bead aesthetics. Furthermore, the Lincoln Electric 11572 features a built-in contactor safety switch which enhances user safety by preventing wire feeding when the torch trigger is not activated.

Technology plays a vital role in the Lincoln Electric 11572’s performance. The unit utilizes the company's proprietary welding technology, which ensures a stable arc and reduces spatter for cleaner welds. The efficient wire feed system works seamlessly to maintain a smooth and consistent feed, reducing the risk of jams and enhancing overall productivity.

Additionally, the machine comes equipped with a user-friendly interface, including easy-to-read settings and controls. This makes it accessible for welders of all skill levels, from beginners to experienced professionals. The welder's versatility is further amplified by its ability to handle gas or gasless welding, depending on the user's preference and project requirements.

In conclusion, the Lincoln Electric 11572 is a dependable solid MIG welder that offers a blend of portability, safety, and advanced welding technology. Its robust features and user-centric design make it an excellent choice for a wide range of applications, enabling users to achieve high-quality results with ease. Whether for industrial use or personal projects, this welding machine promises to deliver performance that meets and exceeds expectations.
Top Page Image Contents