Cylinder may explode if damaged, Iii | Lincoln Electric 11572

iii

SAFETY

iii

WELDING and CuTTING

SPARKS can

cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire.

Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate cir- cuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During Welding, Cutting and Other Hot Work”, available from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

•Away from areas where they may be struck or subjected to physical damage.

•A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturer’s recommendations.

Refer to http://www.lincolnelectric.com/safety for additional safety information.

11572 specifications

Lincoln Electric 11572 is a high-performance welding machine that has garnered attention in the industry for its reliability and innovative technologies. Primarily designed for MIG welding, this unit stands out due to its combination of portability, ease of use, and superior welding capabilities. It caters to both professional welders and DIY enthusiasts, making it a versatile option for a variety of welding tasks.

One of the key features of the Lincoln Electric 11572 is its compact design. Weighing in at just over 30 pounds, it is lightweight enough for easy transportation, allowing users to take it to job sites or different workshop locations without hassle. Despite its portable nature, it does not compromise on performance, providing a robust output that is capable of handling a range of materials, including mild steel, stainless steel, and aluminum.

The machine is equipped with a variable voltage control, which allows users to adjust the output to suit different welding thicknesses and types. This flexibility aids in achieving optimal welds, ensuring a good balance between penetration and bead aesthetics. Furthermore, the Lincoln Electric 11572 features a built-in contactor safety switch which enhances user safety by preventing wire feeding when the torch trigger is not activated.

Technology plays a vital role in the Lincoln Electric 11572’s performance. The unit utilizes the company's proprietary welding technology, which ensures a stable arc and reduces spatter for cleaner welds. The efficient wire feed system works seamlessly to maintain a smooth and consistent feed, reducing the risk of jams and enhancing overall productivity.

Additionally, the machine comes equipped with a user-friendly interface, including easy-to-read settings and controls. This makes it accessible for welders of all skill levels, from beginners to experienced professionals. The welder's versatility is further amplified by its ability to handle gas or gasless welding, depending on the user's preference and project requirements.

In conclusion, the Lincoln Electric 11572 is a dependable solid MIG welder that offers a blend of portability, safety, and advanced welding technology. Its robust features and user-centric design make it an excellent choice for a wide range of applications, enabling users to achieve high-quality results with ease. Whether for industrial use or personal projects, this welding machine promises to deliver performance that meets and exceeds expectations.