Lincoln Electric 11395, 10,000 PLUS manual Maintenance, Safety Precautions, Engine OIL Change

Page 24

D-1

MAINTENANCE

D-1

 

 

 

SAFETY PRECAUTIONS

WARNING

Have qualified personnel do the maintenance work. Turn the engine off before working inside the machine. In some cases, it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the mainte- nance requiring their removal is complete. Always use the greatest care when working near moving parts.

Do not put your hands near the engine cooling blower fan. If a problem cannot be corrected by following the instructions, take the machine to the nearest Lincoln Field Service Shop.

-----------------------------------------------------------------------

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or electrode with skin or wet clothing.

Insulate yourself from work and ground

Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

Use in open, well ventilated areas

or vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.

Do not operate with doors open or guards off.

• Stop engine before servicing.

Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information throughout this operator’s manual and the Engine manual as well.

------------------------------------------------------------

Read the Safety Precautions in the front of this manual and the engine instruction manual before working on this machine.

Keep all equipment safety guards, covers, and devices in position and in good repair. Keep hands, hair, cloth- ing, and tools away from gears, fans, and all other moving parts when starting, operating, or repairing the equipment.

Routine Maintenance

At the end of each day’s use, refill the fuel tank to minimize moisture condensation in the tank. Running out of fuel tends to draw dirt into the fuel system. Also, check the crankcase oil level and add oil if indicated.

CAUTION

Make certain that the oil filler cap is securely tight- ened after checking or adding oil. If the cap is not tight, oil consumption can increase significantly which may be evidenced by white smoke coming from the exhaust.

OIL - Maintenance schedule for changing the oil and oil filter after break-in :

 

KOHLER

SUBARU ROBIN

HONDA

 

CH23S

EH65

GX620KI

 

 

 

6 Months

Oil

100 HRS.

100 HRS.

100 HRS.

Oil Filter

200 HRS.

200 HRS.

1 Year or

200 HRS.

 

 

 

The above schedule is for normal operating condi- tions. More frequent oil changes are required with dusty, high temperature and other severe operating conditions. Refer to the maintenance section of the Engine Owner's Manual for more information.

NOTE: Engine life will be reduced if the oil and oil filter are not changed according to the manufacturer’s recommendation.

ENGINE OIL CHANGE

Drain the oil while the engine is warm to assure rapid and complete draining.

Remove the oil filler cap and dipstick. Remove the yellow cap from the oil drain valve and attach the flexible drain tube supplied with the machine. Push in and twist the drain valve counterclockwise. Pull the valve out and drain the oil into a suitable contain- er.

Close the drain valve by pushing in and twisting clockwise. Replace the yellow cap.

Refill to the upper limit mark on the dipstick with the recommended oil. Tighten the oil filler cap securely.

ENGINE OIL REFILL CAPACITIES

Without oil filter replacement:

1.7 qt. (1.6 liter)-Kohler

1.5 qt. (1.4 liter)-Subaru Robin

1.6 qt. (1.5 liter)-Honda GX620KI

With oil filter replacement:

2.0 qt. (1.9 liter)-Kohler

1.6 qt. (1.6 liter)-Subaru Robin

1.9 qt. (1.8 liter)-Honda GX620KI

RANGER 10,000 PLUS AND RANGER 10,000

Image 24
Contents Ranger 10,000 Plus Lincoln ElectricSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Installation Height Width Depth WeightSafety Precautions Machine GroundingSpark Arrester TowingPRE-OPERATION Service Battery ConnectionsGasoline Welding Output Cables Total Combined Length of Electrode and Work CablesHigh Altitude Operation Angle of OperationInstructions Auxiliary Power 120/240 Volt Dual Voltage ReceptacleDuplex Receptacles Motor StartingType Common Electrical Devices Possible Concerns NoneAuxiliary Power While Welding Simultaneous Welding and PowerStandby Power Connections Power Engine Switch OperationGeneral Description Welder Controls Function and OperationPolarity Switch Range SwitchControl Dial Kohler Subaru Robin HondaSTARTING/SHUTDOWN Instructions BREAK-IN PeriodStarting the Engine Stopping the EngineDiameter Wire Speed Approximate Welding ProcessStick Constant Current Welding TIG Constant Current WeldingStick Auto Accessories K1745-1 Welding GAS Cylinder LPG Tank HolderWire Feed Recommended EquipmentStick TIG WeldingMaintenance Safety PrecautionsEngine OIL Change Engine OIL Refill CapacitiesAIR Cleaner and Other Maintenance OIL Filter ChangeEngine Adjustments BatteryOverspeed is Hazardous Slip RingsTroubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams Ranger 10,000 Plus and Ranger10,000 Enhanced Diagram F-2 Ranger PlusRanger 10,000 Plus Ranger 10,000Ranger 10,000 Plus and Ranger 10,000 Precaucion Warnung