Wagner SprayTech 1720, 2120 Preparing the Sprayer for LONG- Term Storage, Shutdown, Startup

Page 12

STORAGE

SHORT-TERM STORAGE (UP TO 16 HOURS)

Follow these steps when using latex paints only. If using materials that are oil-based, follow the long-term storage steps.

SHUTDOWN

1. Lock the spray gun off.

GX-06/07

GX-08/10

2. Turn the PRIME/SPRAY knob to PRIME.

PRIME

SPRAY

3. Switch the pump OFF, and unplug the sprayer.

o

4.Pour 1/2 cup water slowly on the top of the paint to prevent the paint from drying.

5.Wrap the spray gun assembly in a damp cloth and place it in a plastic bag. Seal the bag shut.

6.Place the sprayer in a safe place out of the sun for short- term storage.

STARTUP

1. Remove the gun from the plastic bag.

2. Stir the water into the paint.

3. Check to be sure that the PRIME/SPRAY knob is set to

PRIME.

4. Plug sprayer in and

PREPARING THE SPRAYER FOR LONG- TERM STORAGE

1.Fill a cup or other container with separating oil (approximately 2 ounces) supplied with the unit and submerge the inlet valve into the oil.

2.Place a rag over the spray hose port, and turn the switch ON (l).

3.When the oil has been sucked from the cup, switch the pump OFF.

4.Insert the pusher stem into the inlet valve. Make sure the pusher stem is inserted fully.

Inlet valve

The pusher stem is designed to do two things:

It holds the oil in the valve to keep the carbide seat from rusting.

Secondly, it will keep the ball off of the seat to prevent any paint residue deposits that will cause the ball to stick to the seat. Paint deposits or rust formed on the carbide seat will cause priming and operation problems during repeated uses.

5.Wipe the entire unit, hose and gun with a damp cloth to remove accumulated paint.

6.Replace the high pressure hose to the paint hose port.

turn the switch to

PRIME

ON.

 

5. Turn the

l

PRIME/SPRAY

SPRAY

knob to SPRAY.

 

6. Test the sprayer on

a practice piece and begin spraying.

English Customer Service: 800-686-8525 12

© 2002 Wagner Spray Tech - All rights reserved.

Image 12
Contents Table of Contents SpecificationsHigh Performance Airless Sprayer Safety Information Read ALL Safety Important Electrical Information Grounding InstructionsComponents and Description ComponentsControls and Functions SETUP--ASSEMBLING the Sprayer Locking and Unlocking the Spray GUNPressure Relief Procedure Before YOU BeginPlugging in the Sprayer Before YOU Prime the SprayerPurging & Priming Your hose is now purged and primed. You are ready to paintSpraying PracticeSpraying Technique Spraying Troubleshooting Cleaning the Spray GUN FilterCleaning the Suction SET Screen Unclogging the Spray TIPCleanup Cleaning the Suction SETMove on to Cleaning the Suction Set Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly GX-08/10Filter Trigger GuardStorage Preparing the Sprayer for LONG- Term StorageShutdown StartupMaintenance AccessoriesDaily Maintenance Extended MaintenanceFluid Section Seal Replacement Instructions Disassembly of the Fluid SectionAssembly of the Fluid Section Troubleshooting ProblemParts List Liste DE PIÈ CES Lista DE Piezas Suction SET Dispositif ’ASPIRATION Juego DE Succió NArticle N de piè ce Description Quantity Articulo0296291 02963430347706 0296262Articulo Pieza# Descripció n Cantidad Article N de piè ce Description QuantitéWagner Spray Tech Corporation Fernbrook LaneMinneapolis, Minnesota Telephone
Related manuals
Manual 44 pages 43.11 Kb