Friedrich ZQ08A10C manual Electrical Parts, Overload Protector, Compressor, Capacitor

Page 7

2.3 ELECTRICAL PARTS

2.3.1 OVERLOAD PROTECTOR

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the nut which fastens the terminal cover.

3. Remove the terminal cover. (See Figure 7)

4. Remove all the leads from the overload protector.

5. Remove the overload protector.

6. Re-install the component by referring to the removal procedure, above.

Figure 7

2.3.2 COMPRESSOR

1.Remove the cabinet. (Refer to section 2.1.2)

2.Discharge the refrigerant system using a FreonTM

Recovery System.

If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the FreonTM. Leave the valve in place after servicing the system.

3. Remove the overload protector. (Refer to section 2.3.1)

4. After purging the unit completely, unbraze the suction and discharge tubes at the compressor

connections.

5. Remove the 3 nuts and the 3 washers whichFigure 8 fasten the compressor.

6.Remove the compressor. (See Figure 8)

7.Re-install the components by referring to the removal procedure, above.

2.3.3 CAPACITOR

1. Remove the control box. (Refer to section 2.1.3)

2. Remove the knobs and the screw which fasten control panel from control box.

3. Remove the screw which located in the front.

4. Open the bottom side of control box.

5. Remove the screw and the clamp which fastens the capacitor.

6. Disconnect all the leads of capacitor terminals.

7. Re-install the components by referring to the removal procedure, above. (See Figure 9)

Figure 9

— 7—

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Room Air Conditioner Service and Parts Manual ZStarTM Preface ContentsItems SpecificationsModels ZQ08A10CControl Locations FeaturesControl only Model Cabinet Disassembly InstructionsMechanical Parts Front GrilleAIR Guide and Blower AIR Handling PartsFAN and Shroud Capacitor Electrical PartsOverload Protector CompressorRotary Switch Power CordThermostat Capillary Tube Refrigerating CycleCondenser EvaporatorPage Pulling Vacuum Installation Hardware InstallationSelect the Best Location Width Minimum 1 1/238mm Window RequirementsStorm Window Requirements Wood PiecesBefore Installation Preparing the Unit for InstallationInstall the Case in the Window To Reverse the Grille Opening Install the AIR Conditioner in the CaseOutside Dimensions Troubleshooting GuideEvaporator Coil Piping SystemIneffective Cooling Troubleshooting GuideFails to Start Name Plate Rating Minimum Maximum Room AIR Conditioner Voltage LimitsComplaint Cause Remedy Complaint Cause Remedy Complaint Cause Remedy Description QTY Schematic DiagramCircuit Diagram Model ZQ08A10CExploded View Model ZQ08A10C Replacement Parts ListControl BOX Assy Use Factory Certified Parts
Related manuals
Manual 28 pages 46.28 Kb

ZQ08A10C specifications

The Friedrich ZQ08A10C is an advanced cooling unit designed to meet the needs of residential and commercial environments. This portable air conditioner is especially notable for its efficiency, convenience, and cutting-edge technologies, making it an ideal choice for those seeking reliable temperature control.

One of the main features of the ZQ08A10C is its impressive cooling capacity. With a power rating of 8,000 BTUs, this unit is capable of effectively cooling spaces up to 350 square feet, making it suitable for large rooms, offices, and even some small apartments. The air conditioner operates quietly, allowing users to enjoy a comfortable indoor climate without disruptive noise.

Efficiency is a critical characteristic of the ZQ08A10C. It is equipped with an Energy Efficiency Ratio (EER) that ensures lower energy consumption compared to traditional air conditioning systems, which translates to lower utility bills. This model also utilizes eco-friendly refrigerant, contributing to a reduced environmental impact while maintaining high performance.

The design of the Friedrich ZQ08A10C prioritizes portability and ease of use. Casters allow for effortless movement from one room to another, making it versatile for various settings. Additionally, the unit features a digital thermostat with a remote control, enabling users to set their desired temperature from a distance. The easy-to-read display provides clear information on temperature settings and operational modes.

Technologically, the ZQ08A10C includes multiple fan speeds and a programmable timer, enhancing user control over the cooling experience. The unit also features a dehumidification function, helping to remove excess moisture from the air, which is essential for maintaining comfort in humid environments.

Maintenance is simplified through the inclusion of a washable filter, promoting clean air circulation and extending the lifespan of the unit. Furthermore, the installation process is straightforward, often requiring no additional tools beyond those included in the packaging.

In summary, the Friedrich ZQ08A10C stands out for its robust cooling efficiency, user-friendly features, and portability. Its innovative technologies and durable performance make it a strong contender in the market of portable air conditioning solutions, suitable for a variety of spaces and settings.
Top Page Image Contents