Friedrich CP08 operation manual How to Install the Unit, Window Requirements

Page 12

12

How to Install the Unit

1.To prevent vibration and excess noise, make sure the unit is installed securely and firmly

2.Install the unit where the sunlight does not shine directly on the unit.

3.The outside of the cabinet must extend outward for at least 12" and there should be no obstacles, such as a fence or wall, within 20" from the back of the cabinet, as it will prevent heat radiation of the condenser.

Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner.

Cooled air

30"~60"

Fence

Awning

Heat radiation

About 1/2"

Over 20"

CAUTION: All side louvers of the cabinet must remain exposed and unobstructed to the outside of the structure.

4.Install the unit with a rear, downward slope, so the back is slightly lower than the front (about 1/4" buble on a level). This will force condensation to flow to the outside.

5.Install the unit with the bottom about 30"~60" above the floor level.

Window Requirements

NOTE: All supporting parts should be secured to firm wood, masonry, or metal.

This unit is designed for installation in standard double hung windows with actual opening widths from 22" to 36".

The top and bottom window sash must open sufficiently to allow a clear vertical opening of 15" from the bottom of the upper sash to the window stool.

22" to 36"

 

 

15" min

Stool

(With frame curtain)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Interior wall

20 1/12" min.

(Without frame curtain)

Offset

1/2" to 11/4"

Sill

Exterior

10

Image 12
Contents Registering Your Room Air Conditioner Page Table of Contents Introduction Before Operating Your UnitFor the Best Cooling Performance and Energy Efficiency Safety Precautions Meanings of symbols used in this manual are as shown belowProperties only Sharp EDGES! The edges of the case can be Sharp How to operate your Friedrich Control and Remote Control OperationsInserting the Remote Control Batteries How to operate your Friedrich ZStar Function ControlsAdjusting the Air Flow Direction Adjusting the Air Flow DirectionAdjusting the vertical louvers left and right will Vent ControlCare and Maintenance Air FilterDrainage Product Features Positioning the Power cordFasten the stopper using 2 screw holes, and lead Out the power cord through slit aHow to Install the Unit Window RequirementsInstallation Kit Contents Suggested Tool RequirementsCabinet Installation Open the window. Mark a line on center of the window stoolType a screws in each support See Fig ScrewType B Sill Support With a Type C Screw . See FigInstallation Instructions Phillips-head screwdriverElectrical Safety Troubleshooting Tips Room AIR Conditioners Limited Warranty De votre climatiseur de pièce CP Line Page Table des matières Avant dutiliser votre appareil Nutilisez Jamais un fil de rallongeMesures de Sécurité Veillez à brancher Correctement votre appareilBords Pointus Fonctionnement de la télécommande Fonctionnement de la télécommandeRemplacement des piles de la télécommande Niveaux High Low MedOff Fermé Met le climatiseur hors tension Med Fan Ventilateur moyenVitesse, sans refroidissement Le plus haut le numéro, le plus grand le refroidirCommande de l’orifice de ventilation Réglage de lorientation du débit dairRéglage de l’orientation du débit d’air Soins et entretien Filtre à airAvant de le remettere en place Installation du matériel Caractéristiques particulières de l’appareilPositionnement du cordon d’alimentation Attachez le taquet en utilisant 2 trous de vis, etInstallation de l’appareil Dimensions de fenêtre minimales22 à 15min. Rebord Volet détanchéité inclus Décalage To 11/4 Seuil ExtérieurContenu du nécessaire d’installation Outils recommandésInstallation du boîtier Choisissez lemplacement qui situera leJoint détanchéité En mousse Boîtier Volet détanchéité Type a pour chaque support Voyez laVoyez la . Réglez lécrou et le boulon Des supports de seuil de manière àÉquilibrer le boîtier Angle avantLectriques Français Source dalimentation Delectricite localeFrançais Garantie limitée Climatiseurs Friedrich Registrar su acondicionador de aire para habitación Model information can be found on the name plate located onPage Contenidos Introducción Antes de poner en funcionamiento su unidadEste símbolo indica la posibilidad de lesiones o daños MaterialesNo lo utilice para propósitos especiales Funcionamiento del control remoto Funcionamiento del control remotoInsertar las baterías del control remoto Seleccione el modo seco dry para el funcionamiento secoCómo hacer funcionar a su Friedrich ZStar Posicionando el control en la marca deseadaAjustar la dirección del flujo de aire Control de ventilaciónAjustar la dirección del flujo de aire Derecha cambiará el flujo horizontalCuidado y mantenimiento Filtro de Aire aDrenaje Instalación de la unidad Funciones del productoInstalación del cable eléctrica Cómo instalar la unidad Requisitos de la ventanaSaliente A 11/4 Dintel Exterior Contenidos de los conjuntos de instalación Requisitos sugeridos de las ventanasInstalación del gabinete Marcada en el centro del asiento de la VentanaUsando Las partes que se muestran en FigNgulo frontal Tornillo Tipo aAgregue la abrazadera de fijación Tipo C ver FigEspañol Page Español Garantia Limitada -PRIMER AÑO Memo Friedrich AIR Conditioning CO
Related manuals
Manual 28 pages 12.45 Kb

CP08 specifications

Friedrich CP08 is a highly regarded portable air conditioning unit designed to provide comfort in a multitude of environments. It is especially popular for applications in homes, offices, and small commercial spaces where traditional air conditioning may not be feasible. The CP08 integrates advanced cooling technologies and user-friendly features to enhance the air conditioning experience.

One of the primary distinctions of the CP08 is its powerful cooling capability. With a cooling capacity of 8,000 BTUs, it can efficiently cool spaces up to approximately 350 square feet, making it ideal for medium-sized rooms. The unit also operates with a reasonable Energy Efficiency Ratio (EER), ensuring that it provides effective cooling without excessive energy consumption.

The CP08 features three cooling modes and three fan speeds, allowing users to adjust the unit according to their ambient conditions and personal preferences. This level of customization ensures that users can maintain a comfortable environment regardless of the outside temperature. Additionally, the unit is equipped with a programmable timer, allowing users to set specific run times, which is convenient for energy savings and automatic operation.

In terms of ease of use, the Friedrich CP08 includes a user-friendly remote control, enabling users to adjust settings from a distance. The integrated LED display shows current settings, while the easy-to-read control panel allows for straightforward operation. The unit's design also includes a washable and reusable air filter, promoting healthy air quality by capturing dust and allergens, and extending the life of the unit.

Another notable feature of the CP08 is its relatively lightweight and portable design, complete with wheels that allow for easy movement between rooms. This makes it an excellent choice for renters or those looking for a flexible cooling solution. The unit also has a quiet operation mode, ensuring that it runs quietly during use, which is particularly beneficial for nighttime cooling or in work settings.

The Friedrich CP08 stands out with its robust build quality, combining durability with efficient performance. This small yet powerful air conditioning unit proves that effective cooling solutions can be both versatile and comfortable, meeting the diverse needs of today’s consumers. Whether used in a bedroom, living room, or workspace, the Friedrich CP08 is designed to deliver reliable performance, making it a worthy investment for anyone seeking portable cooling solutions.