Craftsman 919.72458 owner manual Before Each Start-Up, How to Start

Page 14

5.Run the compressor for 15 minutes. Make sure the drain valve is open and there is minimal air pressure build-up in tank.

6.After 15 minutes, close the drain valve (clockwise). The air receiver will fill to "cut-out" pressure and the motor will stop.

The compressor is now ready for use.

Before Each Start-Up:

1.Place On/Auto/Off lever to "OFF".

2.Pull regulator knob out, turn counter-clockwise until it stops. Push knob in to lock in place.

3.Attach hose and accessories. NOTE: The hose or accessory will require a quick connect plug if the air outlet is equipped with a quick connect.

Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating.

How to Start:

1.Turn the On/Auto/Off lever to "AUTO" and allow tank pressure to build. Motor will stop when tank pressure reaches "cut-out" pressure.

2.Pull the regulator knob out and turn clockwise to increase pressure. When the desired pressure is reached push knob in to lock in place. The compressor is ready for use.

NOTE: Always operate the air compressor in well-ventilated areas free of gasoline or other combustible vapors. If the compressor is being used to operate a sprayer DO NOT place near the spray area.

D24456

14- ENG

Image 14

Contents AIR Compressor Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8Table of Contents Important Safety Instructions Specification ChartSafety Guidelines Definitions Model No 919-724580Hazard What Could HappenWhat can Happen Hazard Never operate the compressor with Risk of FallingResult in serious burns Belt can cause serious injury if theyWhen Transporting Compressor Glossary AccessoriesAccessories Duty CycleUnpacking AssemblyInstallation Location of the Air CompressorExtension Cords Voltage and Circuit ProtectionKnow Your Air Compressor Pump On/Auto Off SwitchOperation Description of OperationBreak-in instructions How to StopBefore Starting Check Valve DrainHow to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain TankMotor Air Filter Inspection and ReplacementAir Compressor Pump Intake and Exhaust Valves Pressure Relief Tube Nut Outlet Nut Check Valve Service and AdjustmentsTo Replace or Clean Check Valve Screwdriver Open position nothing is visibleStorage Troubleshooting Pressure reading Problem Cause Correction Table DES Matières Sears Canada, Inc., Toronto, Ont. M5B 2B8Consignes DE Sécurité Importantes Tableau DES SpécificationsMesures DE Sécurité Définitions Risque D’EXPLOSION OU D’INCENDIE RisqueRisque D’ÉCLATEMENT Risque DE Projection D’OBJETSRisque DE Choc Électrique Risque PAR InhalationRisque DE Chute Risque DE BrûluresRisque Relié AUX Pièces Mobiles Risque Dune Utilisation Dangereuse Accessoires AccessoiresCycle DE Service LexiqueDéballage Emplacement du compresseur dairAssemblage Directives DE Mise À LA TerreRallonges Protection contre la surtension et protection du circuitDescription du fonctionnement UtilisationFamiliarisez-vous avec votre compresseur dair Système de refroidissement non illustré Arrêt de lappareilAvant le démarrage Robinet de vidangeAvant chaque mise en marche Mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du client Vidange du réservoirFiltre à air Inspection et remplacement MoteurTournevis Remplacement ou nettoyage de la soupape de retenueEntretien ET Réglages En position fermée, le disque est visibleRangement Dépannage Problème Cause CorrectifElle doit être remplacée Le moteur ne 50- FR 51- FR D24456 Get it fixed, at your home or ours