Craftsman 919.72458 How to Stop, Before Starting, Break-in instructions, Check Valve Drain

Page 13

Cooling System (not shown): This compressor contains an advanced design cooling system. At the heart of this cooling system is an engineered fan. It is perfectly normal for this fan to blow air through the vent holes in large amounts. You know that the cooling system is working when air is being expelled.

Air Compressor Pump:

Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

Drain Valve: The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use.

Check

Valve

Drain

Valve

Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

Pressure Release Valve: The pressure release valve located on the side of the pressure switch, is designed to automatically release compressed air from the compressor head and the outlet tube when the air compressor reaches "cut-out" pressure or is shut off. The pressure release valve allows the motor to restart freely. When the motor stops running, air will be heard escaping from this valve for a few seconds. No air should be heard leaking when the motor is running, or continuous leaking after unit reaches "cut-out" pressure.

Pressure

Release

Valve

How to Use Your Unit

How to Stop:

1.Set the On/Auto/Off lever to "OFF".

Before Starting

Break-in instructions

Serious damage may result if the

following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the On/Auto/Off lever is in the "OFF" position.

NOTE: If quick connect is installed, pull coupler back until it clicks to prevent air from escaping through the quick connect.

2.Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.)

3.Open the drain valve fully (counter-clockwise) to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

4.Move the On/Auto/Off lever to "ON/AUTO" position. The compressor will start.

13- ENG

D24456

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8 AIR CompressorTable of Contents Safety Guidelines Definitions Specification ChartImportant Safety Instructions Model No 919-724580What Could Happen HazardWhat can Happen Hazard Result in serious burns Risk of FallingNever operate the compressor with Belt can cause serious injury if theyWhen Transporting Compressor Accessories AccessoriesGlossary Duty CycleInstallation AssemblyUnpacking Location of the Air CompressorVoltage and Circuit Protection Extension CordsOperation Pump On/Auto Off SwitchKnow Your Air Compressor Description of OperationBefore Starting How to StopBreak-in instructions Check Valve DrainBefore Each Start-Up How to StartTo Check Safety Valve MaintenanceCustomer Responsibilities To Drain TankAir Compressor Pump Intake and Exhaust Valves Air Filter Inspection and ReplacementMotor To Replace or Clean Check Valve Service and AdjustmentsPressure Relief Tube Nut Outlet Nut Check Valve Screwdriver Open position nothing is visibleStorage Troubleshooting Pressure reading Problem Cause Correction Sears Canada, Inc., Toronto, Ont. M5B 2B8 Table DES MatièresMesures DE Sécurité Définitions Tableau DES SpécificationsConsignes DE Sécurité Importantes Risque Risque D’EXPLOSION OU D’INCENDIERisque DE Projection D’OBJETS Risque D’ÉCLATEMENTRisque PAR Inhalation Risque DE Choc ÉlectriqueRisque Relié AUX Pièces Mobiles Risque DE BrûluresRisque DE Chute Risque Dune Utilisation Dangereuse Cycle DE Service AccessoiresAccessoires LexiqueAssemblage Emplacement du compresseur dairDéballage Directives DE Mise À LA TerreProtection contre la surtension et protection du circuit RallongesFamiliarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Avant le démarrage Arrêt de lappareilSystème de refroidissement non illustré Robinet de vidangeMise en marche Avant chaque mise en marcheResponsabilités du client EntretienVérification de la soupape de sûreté Vidange du réservoirMoteur Filtre à air Inspection et remplacementEntretien ET Réglages Remplacement ou nettoyage de la soupape de retenueTournevis En position fermée, le disque est visibleRangement Problème Cause Correctif DépannageElle doit être remplacée Le moteur ne 50- FR 51- FR D24456 Get it fixed, at your home or ours
Top Page Image Contents