Black & Decker 500 Sample RUN Times, Troubleshooting, Service Information, Care and Maintenance

Page 4

BPS500B ManualENSP 041008.qxp 4/10/2008 10:42 AM Page 6

SAMPLE RUN TIMES

Appliance

Watts*

Run Time**

Product

Watts*

Run Time**

Laptop computer

30

12 h

Table lamp

40

9 h

 

 

 

 

 

 

Inkjet printer

20

16 h

Desktop computer

70

5 h

 

 

 

 

 

 

Cordless phone

5

74 h

17" LCD monitor

35

10 h

 

 

 

 

 

 

Cell Phone

5

74 h

13" TV

50

7 h

 

 

 

 

 

 

Internet modem

10

35 h

Clock radio

6

62 h

Combination of Appliances

Run Time**

Laptop, cordless phone, Internet modem/router

up to 8 h.5

 

 

13" TV, cell phone charger, table lamp

up to 4 h

 

 

Desktop computer, 15" LCD monitor, inkjet printer, Internet modem, cordless phone, table lamp

up to 2 h.5

*Rated power may differ from appliance’s actual average power consumption.

**Run times are based on loads tested under regular operating conditions and are approximate.

TROUBLESHOOTING

General

Problem

Solution

The unit will not power ON

• Connect the unit’s power cord to the wall outlet securely

 

• Make sure that the internal battery is charged (check the Battery

 

Status Icon on the LCD Display). If charge is low, recharge the

 

battery. If battery will not accept a charge after 24 hours, refer to

 

the “Service Information” section.

Appliances connected to unit lose power

A fault condition is present. Check the LCD Display for fault condition

 

message and take the appropriate action (refer to the Fault Condition

 

chart that follows).

Appliances connected to unit malfunction or

Appliances connected to the unit do not accept modified sine wave

overheat

form. Refer to “CAUTION: TO REDUCE THE RISK OF DAMAGING

 

RECHARGEABLE APPLIANCES” on page 3.

Inadequate run time

Make sure that the internal battery is charged (check the Battery

Should the battery need replacing, it is recommended that the unit be returned to manufacturer for battery replacement. Contact Customer Service, toll-free, at (800) 544-6986.

This unit contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required — contact your local authority for information. Failure to comply with local, state and federal regulations can result in fines or imprisonment. For more information on recycling this battery, call toll-free (800) 822-8837.

WARNINGS

•Do not dispose of product in fire as batteries inside this product may explode or leak. •Do not expose the unit containing a battery to fire or intense heat as it may explode.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544- 6986 or visit www.blackanddecker.com.

CAUTION

If the cord becomes damaged, return the entire unit to manufacturer immediately for service/repair.

FULL ONE-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for one year against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

Status Icon on the LCD Display). If charge is low, recharge the battery.

If battery will not accept a charge after 24 hours, refer to the “Service

Information” section.

Fault Conditions

Following is a list of fault conditions, the corresponding LCD Display messages and recommended remedies.

LCD Message

Fault Condition

Recommended Remedy

OVERLOAD

Shows when an overload condition exists (total

Reduce load to 500 watts (continuous).

 

wattage draw exceeds 500 watts) or appliances

Manually reset unit by pressing ON/OFF

 

connected to unit have a surge power that

Pushbutton OFF, then ON again.

 

exceeds 500 watts.

 

SHORT CIRCUIT

Shows when an appliance that is plugged into

Unplug the appliance from the unit and take

PROTECTION

the unit is short-circuited.

appliance to a qualified technician for repair.

 

 

Manually reset unit by pressing ON/OFF

 

 

Pushbutton OFF, then ON again.

LOW BAT

LOW BATTERY WARNING. Shows when

Disconnect load. Recharge battery (refer to

 

the unit’s battery charge level drops below 10.5

“Charging/ Recharging the Unit”).

 

volts. An audible will sound.

 

CARE AND MAINTENANCE

Storage

1.Ideal storage temperature range is 0-25°C (32-77°F).

2.Store and use the unit in a cool, dry place with adequate ventilation for all-around air circulation.

3.Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or dampness.

Battery Replacement/Disposal

This product has a sealed lead acid battery that should be kept fully charged. Charge before first use, immediately after each use, and once every two months if not used regularly. Failure to do this may reduce the battery life dramatically.

SPECIFICATIONS

Transfer Switch:

20 milliseconds

UPS On (no-load current draw):

< 1.5 A (battery drain)

Recharging Time:

Approx. 8 hours from 120V AC

Inverter Specifications

 

Output Power (max. continuous):

500 W

Surge Power (peak):

1000 W

Output Voltage (nominal):

120V AC

Output Frequency:

60 Hz ±2 Hz

Output Wave Form:

Modified sine wave

12 Volt DC Specifications

 

Internal Battery Type:

Sealed lead acid, AGM

Internal Battery Capacity:

40 amp-hours

Internal Battery Voltage:

12 VDC (nominal)

Low Battery Alarm:

10.5 V (nominal)

Low Battery Shutdown:

10.0 V (nominal)

Internal Charger Charging Current:

6 A DC (max.)

USB Charging Ports

 

Output:

Greater than 5 amps

Imported by

 

Black & Decker (U.S.) Inc.,

 

701 E. Joppa Rd.

 

Towson, MD 21286 U.S.A.

RD041008

 

See ‘Tools-Electric’

– Yellow Pages – for Service & Sales

6

7

Image 4
Contents Electromate Before Returning this Product For ANY Reason Please CallEspecificaciones Save this Manual for Future ReferenceSafety Guidelines / Definitions Important Safety InstructionsGeneral Safety Warnings and Instructions for ALL Appliances Battery CautionsFeatures Using the 120 Volt AC Power SupplyUsing the USB Charging Ports Monitoring Power UsageTroubleshooting Service InformationFull ONE-YEAR Home USE Warranty Care and MaintenanceManual DE Instrucciones DEL Electromate Conserve Este Manual Para Futuras ConsultasNormas DE SEGURIDAD/DEFINICIONES Instrucciones Importantes Sobre SeguridadConserve Estas Instrucciones LEA Todas LAS InstruccionesIntroducción CaracterísticasPreparación DE LA Unidad Para EL Primer USO Carga Y Recarga DE LA UnidadDetección DE Problemas Tiempos DE Funcionamiento DE MuestraCuidado Y Mantenimiento Información DEL Servicio Técnico

500 specifications

The Black & Decker 500 is a versatile power tool designed for both amateurs and professionals alike. Known for its reliability and efficiency, this tool is tailored to meet a plethora of household and workshop tasks.

One of the standout features of the Black & Decker 500 is its powerful motor, which operates at a robust speed that allows for swift and accurate cutting, drilling, or sanding. With an adjustable speed setting, users can tailor the operation to match the requirements of different materials, ensuring optimal performance.

The ergonomic design of the Black & Decker 500 enhances user comfort during extended use. It incorporates a lightweight frame that makes it easy to maneuver, while a rubberized grip provides a secure hold, reducing hand fatigue. This thoughtful design ensures that both novices and seasoned experts can use the tool without discomfort.

Another noteworthy characteristic is the tool's adaptability. The Black & Decker 500 is compatible with a wide range of attachments and accessories, transforming it into a multi-functional tool. Whether it's replacing the drill bit for a simple hole or attaching a sanding pad for surface finishing, the tool excels in flexibility.

Safety features are also paramount in the design of the Black & Decker 500. It comes equipped with a safety lock, preventing accidental starts that could lead to injuries. Additionally, the tool is designed to dissipate heat efficiently, ensuring that it can handle extended periods of use without overheating.

The Black & Decker 500 is also equipped with advanced technologies that enhance the overall user experience. Its built-in LED light illuminates the work area, ensuring clear visibility in dim lighting. This is an invaluable feature for intricate tasks that require precision.

Moreover, the tool’s overall durability is commendable. Constructed from high-quality materials, it can withstand the rigors of regular use, ensuring a long lifespan.

In conclusion, the Black & Decker 500 combines power, versatility, and user-friendly features, making it an essential addition to any toolkit. Whether for home improvement projects or professional endeavors, it empowers users to accomplish a wide array of tasks with confidence and ease.