Kenwood NXR-810, NXR-710 Controls and Functions, Repeater Operation, Transceiver Operation

Page 2

CONTROLS AND FUNCTIONS

Front Panel

q

w e r t

 

CH/STATUS

 

 

 

VOLUME

TX

BUSY

POWER

 

 

 

MIC

qSpeaker

wCH/STATUS Display

Two 7-segment digits display the channel number, name, or status.

eVOLUME control

Rotate to adjust the audio.

rPOWER switch

tPOWER indicator

Lights green when power is supplied to the DC 13.2V jack.

o i u y

yMIC jack

Connect a microphone to this 8-pin modular jack.

uProgrammable Function keys

Press these keys to activate their programmable functions.

iBUSY indicator

Lights green while a signal is being received.

oTX indicator

Lights red while transmitting.

Rear Panel

q w

e r t

 

 

REF IN

RX IN

TX OUT

CONTROL

 

 

 

I / O

 

 

 

 

FUSE 15A

 

 

DC 13.2V

TEST/SPKR

 

 

 

 

 

N SYNC

i

u y

qTX OUT jack

Connect a TX antenna or a duplexer to this receptacle.

wCONTROL I/O jack

Connect a repeater controller or a remote panel to this DB25 interface.

eREF IN jack

Connect to a 10 MHz external oscillator.

rRX IN jack

Connect an RX antenna or a duplexer to this BNC receptacle.

tFUSE

Insert 15 A blade fuse into this fuse holder.

yDC 13.2V jack

Connect a 13.2 V DC power supply to this jack.

uN SYNC 1 / 2 jack

This jack is currently not used. Future functions include connecting another repeater or optional device.

iTEST/SPKR jack

Test input/output jack. Connect an external speaker to this jack.

REPEATER OPERATION

Note: Please consult your dealer for programming the repeater.

When power is applied to the unit, the POWER indicator lights:

Green when using the DC jack.

Rotate the VOLUME control to adjust the audio.

The BUSY indicator lights green while receiving a signal and the TX indicator lights red while transmitting.

TRANSCEIVER OPERATION

Receive

Adjust the volume to your desired level. You may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another member in your fleet.

The BUSY indicator lights green while a signal is being received.

Transmit

1Listen to the channel before transmitting, to make sure it is not being used.

2Press the microphone PTT switch, then speak in your normal speaking voice.

The TX indicator lights red while transmitting.

3When you finish speaking, release the PTT switch.



Image 2
Contents Thank YOU PrecautionsInstallation Unpacking and Checking EquipmentTransceiver Operation Controls and FunctionsRepeater Operation Mode D’EMPLOI Fonctionnement DE L’EMETTEUR- Recepteur Commandes ET FonctionsFonctionnement DU Repeteur Manual DE Instrucctiones Funcionamiento DEL Transceptor Controles Y FuncionesFuncionamiento DEL Repetidor Manuale DI Istruzioni Funzionamento DEL Ricetrasmettitore Controlli E FunzioniFunzionamento DEL Ripetitore Einbau BedienungsanleitungGerät Auspacken UND Lieferumfang Überprüfen MikrofonBedienung DES Transceivers Bedienelemente UND FunktionenVerwendung DES Repeaters Gebruiksaanwijzing Bediening Zendontvanger Bedieningselementen EN FunctiesBediening Repeater Kullaniciya Uyarilar Teşekkür EderİzÖnlemler Ekİpmanin Ambalajindan Çikarilmasi VE Kontrol EdİlmesİEL Telsİzİnİn Çalişmasi Kumandalar VE İşlevlerİRöle Tekrarlayici Çalişmasi Αφαιρεση ΤΗΣ Συσκευασιασ ΚΑΙ Ελεγχοσ Εξοπλισμου ΣΑΣ ΕυχαριστουμεΠροφυλαξεισ ΕγκαταστασηΛειτουργια Πομποδεκτη Χειριστηρια ΚΑΙ ΛειτουργιεσΛειτουργια Επαναληπτη