STUDER INNOTEC | COMPACT |
4.9 The Multifunctional Contact
In the COMPACT there is a
Maximum Contact load:-230Vac /16Amp-30Vdc/1A !
With the Push Button 21 „AUXILIARY CONTACT“ the contact can be manually switched on or off independent of programming and the operating situation. The LED 5 “Contact active” shows the state of the contact. The drawing up the screw terminal “AUX CONTACT” is the inactive position mode, LED 5 “Contact active” off.
The switching on and off of this contact can be freely programmed for every operating situation of the COMPACT witch situation is indicated with a LED. There is no limitation to its application and it is left to your wishes and desires as to where and how you would like to use it. The example and the setting of this contact are explained chapter 5.4.2.
In factory we program this for a dysfunction alarm. The contact is active when one of these situations is detected:
Over temperature (LED 10 lit) Overload (LED 11 lit)
Over or less voltage of batteries (LED 12 lit or blinking) COMPACT is turned off manually or with a fault (LED 13 lit)
4.10The Remote Control
As an option a Remote Control can be connected to the COMPACT. All operating controls and displays except from level adjustment are available on the Remote Control. The Remote Control is supplied with a 20m long cable. It can be lengthened to 40m. The Remote Control is suitable for surface mounting on the wall or on to a switch board. It is fixed with 4 screws. The COMPACT can also be programmed with the Remote Control. The Programming is described in the section „Program- ming“.
The output power and the charging currents are displayed on the Remote Control.
COMPACT | INVERTER - CHARGER |
|
| |
TRANSFER |
|
| ||
|
|
| ||
AC IN | AC OUT | A | % | |
|
| |||
|
|
| 160 | |
CHARGER | INVERTER |
| 130 | |
| RESET | 70 | 100 | |
SOLAR CHARGE | 60 | 80 | ||
ALARM | ||||
| (Select) | 50 | 60 | |
EQUALIZE | Over Temp. | 40 | 40 | |
30 | 20 | |||
|
| |||
Program | Overload | 20 | 10 | |
Battery | 10 | 5 | ||
| ||||
Contact active | Low/High | Charger | ||
| Inverter | |||
Contact manual | OFF |
|
| |
AUXILIARY CONTACT | ON/OFF |
|
| |
(Program) | (Change status) |
| ||
In the Remote Control there is an additional Alarm Contact and a Control Input built in. These two functions are available through
|
|
|
|
|
|
|
|
|
| contorl |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Remote | |
! |
|
|
|
|
| |||||
ON/OFF |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 | 3 | 4 |
|
|
COMPACT |
|
|
|
|
|
| 60V/0,5A | |||
|
|
|
|
|
| |||||
Remote control |
|
|
|
| ||||||
|
|
|
| max. | ||||||
Dry contact |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| ||||
only |
|
|
|
|
|
|
| |||
The Control Input is connected in parallel to the ON/OFF- push button. The COMPACT can be switched on or off through this input with an impulse button or an impulse contact.
Order Number for Remote Control:
Dimensions: H x B x T / 111.5 x 136.5 x 25mm
User manual | COMPACT V4.0 E | 18 |