STUDER INNOTEC | COMPACT |
5.3.2Set the voltage and timing
threshold
The programming is done in accordance with the following steps:
Push and hold down, the Push Button 21 (Program) and the Push Button 19 (Change status) for minimum 2 seconds simultaneously.
With the Push Button 20 (select) select with of the battery level and the absorption time to be changed.
3 |
|
|
|
|
|
|
| 20 |
| RESET ALARM |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| lock |
|
|
|
|
| 14 |
|
| 10 |
| Over Temp |
|
|
|
|
|
|
| ||||
4 |
|
|
| 15 |
|
| 11 |
| Overload | |
|
|
|
|
| ||||||
|
|
|
|
| 12 |
| Batt Low/High | |||
5 |
|
|
| 16 |
|
|
| |||
|
|
|
|
| ||||||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||
6 |
|
|
| 17 |
|
| 13 |
| OFF | |
|
|
| ||||||||
|
|
|
|
|
|
|
|
| ||
21 |
|
|
| 18 | 19 |
| ON/OFF | |||
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| (Change status) |
These four red LED show the function set:
Low voltage | LED 13 |
Float charge | LED 12 |
Absorption (End of charge) | LED11 |
Equalization | LED 10 |
Absorptions Time | LED 10/11/12/13 |
With the Push Button 19 (Change status) set the desired parameter (voltage or the time) to modify (LED 14/15/16/17/18). Push Button 19 (Change status) to set the desired value according to the table 5.3.1.
If desired, repeat the operation with any other parameter (voltage or time) to be changed.
If during 10 seconds no buttons are pressed, the selected values are automatically stored and the COMPACT switches back in to the normal operating status.
The voltage levels and times changed through programming are only first active with the next charge cycle!
The voltage level which are not suitable can greatly reduce the battery life or could even destroy it ! Therefore check beforehand with your battery supplier.
5.4Programming the auxiliary contact
5.4.1Principle
The Auxiliary Contact can be basically programmed for any operating situation of the COMPACT which is indicated with a LED. The programming is possible for one or more operating situations. If the contact is programmed for many situations, it is activated as soon as the COMPACT finds itself in any one of the programmed situations. That means that the work of the contact meets that of the logic
5.4.2The programming of the Auxiliary Contact is carried out in the following Steps
The Push Button 21 (Program) press down for min. 2 seconds. The LED 4 „Program“ is lit as an indication, that the COMPACT is in program mode.
A lit LED shows the programmed condition for the auxiliary contact. (LED 10/11/12/13 factory setting)
With the Push Button 20 (select), select the desired condition in which the contact should be activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If desired, with the Push Button 20 (select) select another condition in which the contact should be activated.
With the Push Button 19 (Change status) confirm or change the status for this condition.
If during 10 seconds no buttons are pushed, then the settled values are automatically stored and the COMPACT switches back to normal operating condition.
User manual | COMPACT V4.0 E | 20 |