AVOID GASEOUS AREAS
Do not operate electric tools in gaseous or explosive atmo- spheres. Motors in these tools normally spark, and may re- sult in a dangerous condition.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease.
CONNECTING THE TOOL
Before connecting the tool to a power source (receptacle, outlet, etc.), be sure voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in serious injury to the user — as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor.
!Some dust created by power sanding, WARNING sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•Lead from
•Crystalline silica from bricks and cement and other masonry products, and
•Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
!This product contains a chemical known to the WARNING State of California to cause cancer.
!WARNING Read all safety warnings and all instructions provided with the working
stand and the power tool to be mounted. Failure to follow the warnings and instructions may result in electric shock, fire and /or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains- operated (corded) power tool or
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments or changing accessories. Accidental starting of the power tool is a cause of some accidents.
Properly assemble the working stand before the mounting the tool. Proper assembly is important to prevent risk of collapse.
Securely fasten the power tool the working stand before use. Power tool shifting on the working stand can cause loss of control.
Place the working stand on a solid, flat and level surface. When the working stand can shift or rock, the power tool or work piece cannot be steadily and safely controlled.
Do not overload the working stand or use as ladder or scaffolding. Overloading or standing on the working stand cause the stand to be
Use only Skil replacement parts. Any others may create a hazard.
Specific Safety Instructions for X-Bench
Read and understand all instructions for use of X- Bench and insert plates with tools. Failure to follow all instructions listed below may result in serious personal injury.
Use only with Skil accessory insert plates (jig saw, drill press, belt sander and router).
The stamped rails or clamps may have sharp edges.
Be careful in handling the bench to prevent being cut.
Fully assemble and tighten all the fasteners required for this stand. Also remember to occasionally check the stand and make sure it is still tight. A loose stand is unstable and may shift in use and cause serious injury.
Turn tool switch and table switch control off and disconnect power before mounting tools to the stand. Unintended startup during assembly can cause injury.
Know how to shut off the power to the tool in an emergency. Position yourself such that you can reach the switch control box while using the cut channel or the tool attachments.
Before operating make sure the entire unit is placed on a solid, flat, level surface. Serious injury could occur if tool is unstable and tips.
Never stand on table or use as ladder or scaffolding.
Serious injury could occur if the table is tipped or the
cutting tool is accidentally contacted. Do not store materials on or near the table such that it is necessary to stand on the table to reach them.
Do not load with more than 250 lbs. This table when fully set and clamps are tightened is maximum rated to 250 lbs. Table could collapse under additional loads.
Do not use as storage shelf. This table is not intended
to be a storage shelf.
Do not store
Use only Skil replacement parts. Any others may create
a hazard.
Don’t use with work pieces that cannot be properly secured to the
Oversized work pieces may cause instability while cutting and you may not be able to shut off the power in an emergency.
Insure wood/workpiece is properly positioned before cutting. Incorrectly positioned workpiece may cause you to inadvertently cut into the
3.