Hitachi C 10FR instruction manual Assembly and Adjustments

Page 10

ASSEMBLY AND ADJUSTMENTS

ESTIMATED ASSEMBLY TIME 25~40 MINUTES FOLDING THE STAND (Fig. A-1)

1.Release the stand hook (1).

2.Unfold the wider leg set (2). Pull the lever (3) downward and push it to lock in place. Then, put down the wider leg set on the ground.

3.Lift the stand up and unfold the narrower leg set (4).

4.Pull the lever downward and push it to lock in place. NOTE: Make sure the stand is locked securely.

Fig. A-1

1

8 7

11

9

10

4

2

6

3

5

ASSEMBLING THE ROLLER WHEEL (Fig. A-1)

Attach the roller wheel (7) to roller wheel bracket using square neck bolt (8) and nut (9) as shown.

INSTALLING THE DUST COLLECTION ELBOW (Fig. A-1)

1.Align the dent with the slot on the exhaust port. Install

the dust collection elbow (6) onto the exhaust port. NOTE: The elbow can be used to attach either the dust bag or a vacuum hose to remove sawdust from the work area.

ASSEMBLING TABLE SAW TO STAND (Fig. A-1,A-2)

1.Place stand on level surface and adjust front right adjustable stand pad (5) to make stand stable.

2.Place table saw on the top of stand aligning holes in base with holes in stand.

3.Insert four hex. head bolts (6) through flat washer and holes in base and stand.

4.Tighten all four bolts.

NOTE: Do not over tighten bolts holding saw to stand. This will damage the saw base.

5.Carefully set the saw in its upright position on a clean level surface.

6.Thread the support rod (10) into the socket (11) at the rear of stand. Adjust the adjustable foot (12) properly.

Fig. A-2

6

6

12

FOLDING THE TABLE SAW/STAND (Fig. A-1, A-3)

1.Release the lever of the narrower leg set and keep the lever on top. Hold the table and lift the saw up just above the ground and fold up the narrower leg set. NOTE: The narrow leg set can be held by a "spring clip" .

2.Then reposition on the saw onto the ground. Release the lever of the wider leg and keep the lever on top set then fold the leg set up into position.

3.Then fix the legs with stand hook.

SETTING UP THE TABLE SAW/STAND (Fig. A-3)

1.Release the stand hook.

2.Unfold the wider leg set and lock the lever in place.

3.Put down the wider leg set on the ground, lift the saw up and unfold the narrower leg set.

4.Pull the lever downward and lock into place. NOTE: Make sure the saw is locked in position securely before operation.

Fig. A-3

FOLDING

SET-UP

—10 —

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 10FR Hitachi Authorized Service Centers Motor SAW Product SpecificationsYES Power Tool Safety Check for Damaged or Loose PartsTable SAW Safety Extension Requirements Electrical Requirements and SafetyPower Supply Requirements Guidelines for Extension CordsTools Needed for Assembly Accessories and AttachmentsCarton Contents Unpacking Your Table SAW Know Your Table SAW Front of Table SawAssembly and Adjustments Keeping the Area Clean Installing and Changing the Blade Fig. H, I, J RIP Fence Fig. GBlade Guard Assembly Fig. K, L, M Installing Table Side Extensions Fig. NAdjusting Rear Table Extension Installing Table Side EXTENSIONS- contd Fig. OInstalling Rear Table Extension Fig. P RIP Fence Adjustment Fig. QStop RIP Fence Indicator Adjustment Fig. QAdjusting the 90 and 45 Positive Stops Fig. Q-1, Q-2, Q-3 Blade Tilt PointerAdditional blade adjustments Fig. S Blade Parallel to the Miter Gauge Groove Fig. R, SOperation Basic SAW OperationsCutting Operations Ripping Fig. WBevel Crosscutting Fig. Z Bevel RippingRipping Small Pieces Compound Miter Crosscutting Fig. AAMaking the side Mitering Fig. BBAuxiliary Fence Fig. CC-1 Making the base Putting it togetherMaintaining Your Table SAW MaintenanceLubrication Troubleshooting Guide Symptom Possible Causes Corrective ActionPush Stick Parts List for Schematic a Parts ListJOB Site Table SAW Model NO. C10FR JOB Site Table SAW Model NO. C10FR JOB Site Table SAW Model NO. C10FRPage Hitachi Koki Canada Co
Top Page Image Contents