Hitachi C 10FR instruction manual Blade Parallel to the Miter Gauge Groove Fig. R, S

Page 16

BLADE PARALLEL TO THE MITER GAUGE GROOVE (Fig. R, S)

WARNING

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

WARNING

To prevent personal injury:

Always disconnect plug from the power source when making any adjustments.

This adjustment must be correct or kickback could result in a serious injury and accurate cuts can not be made.

1.Remove the yellow switch key and unplug the saw.

2.Move the blade guard out of the way.

3.Raise the blade to the highest position and set at the 0° angle (90° straight up).

4 Select and mark, with a felt tip marker, a blade tooth having a “right set”.

5.Place the combination square base (1) into the right side miter gauge groove (2). (Fig. R)

6.Adjust the rule so it touches the front marked tooth and lock ruler so it holds its position in the square assembly.

7.Rotate the blade bringing the marked tooth to the rear and about 1/2 inch above the blade.

8.Carefully slide the combination square to the rear until the ruler touches the marked tooth.

9.If the ruler touches the marked tooth at the front and rear position, no adjustment is needed at this time. If not, perform adjustment procedure described in next section.

Fig. R

2

1

Additional blade adjustments (Fig. S)

The adjusting mechanism is located on top of blade height adjusting hand wheel under the tabletop. If the front and rear measurements are not the same, adjust the alignment by the mechanism as follows:

If the blade is partial to right side:

1.Loosen the two nuts (1) and the right side screw, then adjust the left side screw.

2.Tighten the nuts (1) and the right screw and remeasure, as described in steps 4 to 9 in the prior section.

If the blade is partial to left side:

3.Loosen the two nuts (1) and the left side screw, then adjust the right screw.

4.Tighten the nuts (1) and the left screw and remeasure, as described in steps 4 to 9 in the prior section.

5.Recheck blade clearance making sure that the blade does not hit the table insert or other parts when at the 90° and 45° settings.

Fig. S

1

— 16 —

Image 16
Contents 10FR Hitachi Authorized Service Centers Motor SAW Product SpecificationsYES Power Tool Safety Check for Damaged or Loose PartsTable SAW Safety Electrical Requirements and Safety Power Supply RequirementsExtension Requirements Guidelines for Extension CordsTools Needed for Assembly Accessories and AttachmentsCarton Contents Unpacking Your Table SAW Know Your Table SAW Front of Table SawAssembly and Adjustments Keeping the Area Clean Installing and Changing the Blade Fig. H, I, J RIP Fence Fig. GBlade Guard Assembly Fig. K, L, M Installing Table Side Extensions Fig. NInstalling Table Side EXTENSIONS- contd Fig. O Installing Rear Table Extension Fig. PAdjusting Rear Table Extension RIP Fence Adjustment Fig. QRIP Fence Indicator Adjustment Fig. Q Adjusting the 90 and 45 Positive Stops Fig. Q-1, Q-2, Q-3Stop Blade Tilt PointerAdditional blade adjustments Fig. S Blade Parallel to the Miter Gauge Groove Fig. R, SOperation Basic SAW OperationsCutting Operations Ripping Fig. WBevel Ripping Ripping Small PiecesBevel Crosscutting Fig. Z Compound Miter Crosscutting Fig. AAMitering Fig. BB Auxiliary Fence Fig. CC-1 Making the baseMaking the side Putting it togetherMaintaining Your Table SAW MaintenanceLubrication Troubleshooting Guide Symptom Possible Causes Corrective ActionPush Stick Parts List for Schematic a Parts ListJOB Site Table SAW Model NO. C10FR JOB Site Table SAW Model NO. C10FR JOB Site Table SAW Model NO. C10FRPage Hitachi Koki Canada Co