Hitachi C 10FR instruction manual Bevel Ripping, Ripping Small Pieces, Bevel Crosscutting Fig. Z

Page 19

BEVEL RIPPING

This cut is the same as ripping except the blade bevel angle is set to an angle other than "0".

WARNING

Cut only with the workpiece and the fence on the right side of the blade.

RIPPING SMALL PIECES

WARNING

Avoid injury from the blade contact. Never make through saw cuts narrower than 1/2" wide.

1.It is unsafe to rip small pieces. Instead, rip a larger piece to obtain the size of the desired piece.

2.When a small width is to be ripped and your hand cannot be safely put between the blade and the rip fence, use one or more push sticks to move the workpiece.

CROSSCUTTING (Fig. Y)

WARNING

To prevent serious injury:

Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.

Keep both hands away from the blade and the path of the blade.

1.Remove the rip fence and place the miter gauge in the left side groove.

2.Adjust the blade height so it is 1/8" higher than the top of the workpiece.

3.Hold the workpiece firmly against the miter gauge with the blade path in line with the desired cut location. Move the workpiece to one inch distance from the blade.

4.Start the saw and wait for the blade (1) to come up to full speed.

5.Keep the workpiece (2) against the face of the miter gauge (3) and flat against the face of the gauge and flat against the table. Then slowly push the workpiece through the blade. (Fig. Y)

6.Do not try to pull the workpiece back with the blade turning. Turn the switch OFF, and carefully slide the workpiece out when the blade is completely stopped.

USING WOOD FACING ON THE MITER GAUGE (Fig. Y-1) Slots are provided in the miter gauge of attaching an auxiliary facing (1) to make it easier to cut very long or short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach with screws. Make sure the facing does not interfere with the proper operation of the sawblade guard. When cutting long workpieces, you can make a simple support by clamping a piece of plywood to a sawhorse.

Fig. Y

3

 

 

2

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. Y-1

1

BEVEL CROSSCUTTING (Fig. Z)

This cutting operation is the same as crosscutting except the blade is at bevel angle other than 0 .

1.Adjust the blade (1) to the desired angle, and tighten the blade bevel lock knob.

2.Always work to the left side of the blade. The miter gauge (3) must be in the left side groove (2).

Fig. Z

31

2

COMPOUND MITER CROSSCUTTING (Fig. AA)

This sawing operation is combining a miter angle with a bevel angle.

1.Set the miter gauge (3) to the desired angle. Use only the left side groove (2).

2.Set the blade (1) bevel to the desired angle.

3.Carefully push the miter gauge to begin the cutting operation.

Fig. AA

3 2 1

— 19 —

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 10FR Hitachi Authorized Service Centers Motor SAW Product SpecificationsYES Check for Damaged or Loose Parts Power Tool SafetyTable SAW Safety Guidelines for Extension Cords Electrical Requirements and SafetyPower Supply Requirements Extension RequirementsTools Needed for Assembly Accessories and AttachmentsCarton Contents Unpacking Your Table SAW Front of Table Saw Know Your Table SAWAssembly and Adjustments Keeping the Area Clean RIP Fence Fig. G Installing and Changing the Blade Fig. H, I, JInstalling Table Side Extensions Fig. N Blade Guard Assembly Fig. K, L, MRIP Fence Adjustment Fig. Q Installing Table Side EXTENSIONS- contd Fig. OInstalling Rear Table Extension Fig. P Adjusting Rear Table ExtensionBlade Tilt Pointer RIP Fence Indicator Adjustment Fig. QAdjusting the 90 and 45 Positive Stops Fig. Q-1, Q-2, Q-3 StopBlade Parallel to the Miter Gauge Groove Fig. R, S Additional blade adjustments Fig. SBasic SAW Operations OperationRipping Fig. W Cutting OperationsCompound Miter Crosscutting Fig. AA Bevel RippingRipping Small Pieces Bevel Crosscutting Fig. ZPutting it together Mitering Fig. BBAuxiliary Fence Fig. CC-1 Making the base Making the sideMaintaining Your Table SAW MaintenanceLubrication Symptom Possible Causes Corrective Action Troubleshooting GuidePush Stick Parts List for Schematic a Parts ListJOB Site Table SAW Model NO. C10FR JOB Site Table SAW Model NO. C10FR Model NO. C10FR JOB Site Table SAWPage Hitachi Koki Canada Co
Top Page Image Contents