TROUBLESHOOTING GUIDE (cont’d)
| Problem |
| Possible Cause |
| Service Instructions |
7. Water leaking from rear of | a. Worn or defective vacuum breaker. | a. Remove vacuum breaker cover | |||
| toilet bowl. |
|
|
| and look into top of vacuum |
|
|
|
|
| breaker. Flush toilet. If water leaks |
|
|
|
|
| during flush, vacuum breaker |
|
|
|
|
| needs to be replaced. |
|
| b. Loose vacuum breaker. | b. Secure vacuum breaker connection. | ||
|
| c. | Cracked or defective toilet bowl. | c. | Replace toilet bowl. |
|
|
|
| ||
8. | Water is leaking from the | a. Clamp ring my be loose. | a. Remove plastic base cover (on | ||
| base/toilet connection. |
|
|
| applicable models) and tighten the |
|
|
|
|
| clamp ring. |
|
| b. Ball seals may be worn or defective. | b. Replace ball seals. | ||
|
|
|
| ||
9. | Vacuum pump running too | a. Water leaks out of bowl between | a. Leave small amount of water in | ||
| often between flushes. |
| flush ball and ball seal. |
| bowl. If water is sucked from bowl, |
| (See Vacuum Tester |
|
|
| see problems 1 and 2. |
| Information on page 6.) | b. Vacuum line leak. | b. Tighten all connections at toilet, | ||
|
|
|
|
| vacuum generator or vacuum |
|
|
|
|
| holding tank (including hose |
|
|
|
|
| clamps and threaded spin nuts). If |
|
|
|
|
| leaks persists, contact SeaLand |
|
|
|
|
| Product Customer Service. |
|
|
| |||
10.Vacuum pump will not | a. A vacuum leak exists. | a. See problem 8b. | |||
| shut off. | b. Insufficient vacuum (pump creates | b. Isolate pump and use vacuum | ||
|
|
| less than 10 inches Hg). |
| gauge to check vacuum levels. |
|
|
|
|
| Could be a plugged discharge line |
|
|
|
|
| or worn duckbill valves. |
|
| c. Faulty vacuum switch (pump | c. Replace vacuum switch. | ||
|
|
| creates more than 10 inches Hg). | d. See wiring diagram to check for | |
|
| d. Improper wiring. | |||
|
|
|
|
| proper wiring. |
|
| e. Bellows not pumping. | e. Tighten set screw in eccentric to | ||
|
|
|
|
| motor shaft. Otherwise, check for |
|
|
|
|
| damage to bellows and motor |
|
|
|
|
| shaft. Replace if necessary. |
|
|
| |||
11. Vacuum pump will not run. | a. No electrical power. | a. Check input power, circuit breaker | |||
|
|
|
|
| and fuse. |
|
| b. Loose or broken electrical wiring. | b. Tighten or reconnect wires at | ||
|
|
|
|
| vacuum pump and tank, vacuum |
|
|
|
|
| generator, or vacuum holding tank. |
|
| c. | Improper electrical connections. | c. | Be sure wires at vacuum switch |
|
|
|
|
| are connected to “B” terminals. |
|
| d. Faulty vacuum switch. | d. Check vacuum switch. Short across | ||
|
|
|
|
| “B” terminals with jumper wire. |
|
| e. Faulty motor. | e. Replace motor. | ||
|
| f. | f. | Empty the holding tank. | |
|
|
| |||
12.Vacuum pump is running too | a. Gear motor is worn or defective. | a. Check motor and replace if | |||
| slow, overheating, blowing |
|
|
| necessary. |
| fuses or circuit breaker. | b. Plugged vent line or vent filter. | b. Disassemble and clean out vent | ||
|
|
|
|
| line. Replace vent filter if |
|
|
|
|
| necessary. |
|
| c. | Blockage in discharge line. | c. | Disassemble and clean discharge |
|
|
|
|
| line. Be certain that |
|
|
|
|
| (duckbill valves) and seacock are |
|
|
|
|
| in proper position. |
|
| d. Improper wire size. | d. Wire size too small. Check | ||
|
|
|
|
| electrical diagram for proper wire |
|
|
|
|
| size for voltage of pump used. |
|
| e. Improper voltage. | e. Check input power for low voltage. | ||
|
| f. Vacuum pump bellows clogged | f. | Remove and clean bellows | |
|
|
| with tissue. |
| assembly. (When flushing toilet, |
|
|
|
|
| use of more water may alleviate |
|
|
|
|
| this problem.) |
|
|
|
|
|
|
8