Festool TS 55 EQ Cutting Non-Wood Materials, Soft Plastics, Brittle Plastics, Thin Aluminum

Page 20

Cutting Non-Wood Materials

Soft Plastics

Soft plastics such as polypropylene won’t chip, but they will melt. Therefore, a more aggressive cut with the blade set deeper will reduce the melting.

Too shallow of a blade depth and the plastic will be more prone to melting.

Too deep of a blade depth and the teeth marks from the blade will be more prevalent.

Any of the fine-tooth blades with a slow motor speed will cut this material with good results.

Clean up the cut edges with a cabinet scraper.

Brittle Plastics

Brittle plastics will both melt and chip, so cutting them is problematic with most other saws. The TS 55 works great for cutting this type of material.

Set the blade depth very shallow to reduce chipping.

Set the motor speed very low to reduce melting.

Use any one of the finer tooth blades for good results, but the negative hook aluminum and plastic blade provides the best results.

In clear plastics such as acrylic, if the cut is milky white, it is a sign of melting. Note how the cut to the right is transparent.

Thin Aluminum

The problem with cutting thin aluminum sheet is that the blade teeth can catch the edge of the sheet, and cut more aggressively than expected. To reduce this, you want the teeth moving nearly parallel with the aluminum surface (a shallow blade depth).

The ultra-thin aluminum shown in the example was cut best with the fine crosscut blade. The positive hook angle of the blade kept the flexible aluminum tight to the guide rail in a sheering cut.

For slightly thicker, less flexible pieces of aluminum, the negative hook angle, aluminum cutting blade works best because it cuts less aggressively.

Extruded Aluminum

Care needs to be taken when cutting extruded aluminum because the blade may cut more aggressively than expected on the various surfaces of the stock. This is most noticeable with thin-walled extrusions.

With thin-walled extrusions, try to keep the blade teeth parallel to the walls (see image above).

With thick-walled extrusions, try to keep the blade teeth perpendicular to the walls (see image to the right).

Use the negative hook angle, aluminum-cutting blade, and a moderate speed setting.

Be prepared for the blade to catch unexpectedly as the cutting angle changes with each facet of the extruded shape.

20

TS 55 EQ Circular Saw

Image 20
Contents TS 55 EQ Warranty Conditions of 1+2 WarrantyFestool Limited Warranty Liability StatementContents General Safety Rules Specific Safety Rules for Circular Saws ServiceCauses and Prevention of Kickback Respiratory Exposure WarningTechnical Specifications Tool DescriptionSingle-Point Entry Setup and AdjustmentsSetting up a New Saw Adjusting the Guide Rail Gib Cams Trimming the Guide Rail Splinter GuardReplacing and Adjusting the Riving Knife Trimming the Outrigger Splinter GuardChanging the Sawblade Sawblade Checks and WarningsRemoving the Sawblade Replacing the SawbladeSetting the Blade Perpendicular to the Sole Plate Adjustment ProcedureAdjusting the 45º Bevel Stop Matching the TS 55 to an Existing Guide RailOperation Setting the Blade DepthSetting the Motor Speed Using the Outrigger Splinter Guard Turning On the SawSetting the Bevel Angle Using the Guide StopUsing Dust Extraction Tips for Successful Straight-Lining ApplicationsStraight-Lining Rough Lumber Crosscutting and Trimming Tips for Successful CrosscuttingGeneral Procedure Plunge CuttingCutting Non-Wood Materials Soft PlasticsBrittle Plastics Thin AluminumAccessories SawbladesGuide Rail Accessory Kit Guide RailsDust Cover Rip Fence Parallel GuideStacking Systainers Systainer System ContainerParts of the Systainer Troubleshooting Symptom Possible CausesMaintenance Routine MaintenanceKeep the Saw Clean Adjust and Inspect the SawReplacing the Guide Rail Gib Cams Replacing the Guide Rail Splinter GuardProcedure Changing the Motor Brushes