Porter-Cable PCB270TS instruction manual Table of Contents

Page 2

TABLE OF CONTENTS

SECTION

PAGE

PRODUCT SPECIFICATIONS

2

CALIFORNIA PROPOSITION 65

2

SAFETY GUIDELINES - DEFINITIONS

3

POWER TOOL SAFETY

4

TABLE SAW SAFETY

5

ELECTRICAL REQUIREMENTS AND SAFETY

7

TOOLS NEEDED FOR ASSEMBLY

8

CARTON CONTENTS

9

KNOW YOUR TABLE SAW

11

GLOSSARY OF TERMS

12

ASSEMBLY AND ADJUSTMENTS

13

OPERATION

23

MAINTENANCE

29

TROUBLESHOOTING GUIDE

30

ACCESSORIES AND ATTACHMENTS

31

PARTS LIST

33

WARRANTY

38

PRODUCT SPECIFICATIONS

 

MOTOR

 

SAW

 

Type

Induction

Table Size

27-1/8 in. x 20-1/8 in.

Amps

 

 

(688 mm x 512 mm)

15 / 7.5

Table Extensions

Right & Left

Voltage

120 / 240

Extension Fence Capacity

30 in. (762 mm) Right

Hz

60

Blade Size

10 in. (254 mm)

RPM (no load)

3450

Blade Arbor

5/8 in. (15.9 mm)

Overload Protection

YES

CUTTING CAPACITY

 

MITER GAUGE

YES

Maximum Cut Depth @ 90°

3-1/2in.(88.9 mm)

RIP FENCE

YES

Maximum Cut Depth @ 45°

2-1/4 in.(57.1 mm)

 

 

Maximum Dado Cut Width

13/16 in.(20.6 mm)

 

 

Maximum Dado Blade Diameter.. 8 in. (203.2mm)

!WARNING

To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Use a seperate electrical circuit for your tools. To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection. This table saw is wired at the factory for 110-120/220-240 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere or 220-240 Volt / 7.5 Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

CALIFORNIA PROPOSITION 65

!WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead-based paints,

•Crystalline silica from bricks and cement and other masonry products, and

•Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

 

Use of this tool can generate and/or disperse dust, which may cause serious and permanent

! WARNING

respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

 

appropriate for the dust exposure. Direct particles away from face and body.

 

2009/12

– 2 –

Printed in Taiwan

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Advertencia Léase Este Table of Contents Prohibition Support and Clamp WorkPower Tool Safety General Safety Instructions Before Using this Power ToolTable SAW Safety Kickbacks Grounding Instructions Electrical Requirements and SafetyPower Supply and Motor Specifications Guidelines for Extension CordsVolt Single Phase Operation Supplied Not SuppliedCarton Contents Unpacking Your Table SAW Know Your Table SAW Glossary of Terms Assembly and Adjustments Assembling Stand FIG. A~IAssembling Table SAW to Stand FIG. J Moving Table SAW and Stand FIG. JRiving knife storage Fig. P Storage FIG. L ~ RAnti-kickback pawl storage Fig. L Power cord storage Fig. R Fig. P Miter gauge storage Fig. QBlade Tilting Handwheel FIG Installing a Blade FIG. WAdjusting the 90 and 45 Positive Stops FIG. X, Y, Z Blade Elevation Handwheel FIGBlade Tilting Indicator FIG. AA Stop Fig. X, Y 45º Stop Fig. X, ZFig. BB Installing Blade Guard Assembly FIG. FF, GG Fig. EEInstalling the RIP Fence FIG Installing the Miter GaugeAdjusting the Miter Gauge FIG. HH RIP Fence Adjustment FIG. JJFig. KK Operation Basic SAW OperationsRipping FIG. PP Setting Bevel Angle FIG. QQCutting Operations Bevel RippingCrosscutting FIG. RR Using Wood Facing on the Miter GaugeRipping Small Pieces Miter Cuts FIG Using Wood Facing on the RIP Fence FIG. WWBevel Crosscutting FIG. TT 240V Operation Changing Wires FIG. YY, ZZ Dado Cuts FIGFig. ZZ Maintaining Your Table SAW MaintenanceGeneral Maintenance LubricationProblem Possible Causes Corrective Action Troubleshooting GuideReplacement Parts Service and Repairs 2WHW Dado Insert Plate Accessories and AttachmentsAccessories Push Stick Pattern Push Stick ConstructionParts List MM Stationary Table SAW Parts List for Table SAWMM Table SAW Schematic for Table SAW MM Stationary Table SAW Parts List & Schematic for Stand Description Size QtyMM Stationary Table SAW Parts List & Schematic for Motor TerminalPage Warranty Three Year Limited Warranty
Related manuals
Manual 38 pages 37.67 Kb
Top Page Image Contents