Porter-Cable PCB270TS Fig. P Miter gauge storage Fig. Q, Power cord storage Fig. R

Page 16

Fig. P

1

2

Miter gauge storage (Fig. Q)

Storage for miter guage (1) is located on the right side of the stand. Hang the miter gauge on the hook (2).

Fig. Q

1

ASSEMBLING THE TABLE EXTENSION (FIG. S)

1.Place the left table extension next to the saw table, aligning the mounting holes (1).

2.Bag “Q” - Place three bolts with washers (2) and thread in mounting holes.

3.Place a straight edge or combination square on the saw table, across the table extension.

4.Adjust the mounting bolts (2) until the extension is flush with the saw table, and tighten.

NOTE: Extensions will not be flush on outer edges at this time until rails are installed.

5.Repeat these procedures for the right table

extension.

2

Fig. S

1

2

Rip fence storage (Fig. R)

Storage brackets for the rip fence (1) is located on the left side of the stand. Place the rip fence on the two hooks (2).

Power cord storage (Fig. R)

Storage for the power cord (3) is located on the left side of the stand. Wrap the power cord onto the brackets (4) when saw in not in use. This can prevent damage to the cord.

Fig. R

4

3

 

 

 

1

 

ASSEMBLING THE FRONT AND REAR TABLE RAIL (FIG. T, U)

Assembly the front rail (Fig. T)

1.Identify the right front rail (1) and the left front rail (2) by rail scales (3).

2.Bag “R” - Attach the right front side cover (4) into right front table rail (1). Repeat for the left front rail.

3.Bag “S” - Place four long hex bolts (5), two short hex bolts (6) through the holes at the front table edge. Screw the square nuts (7) onto each bolts.

NOTE: Keep the bolts and square nuts loosened before attaching front rail.

4.Attach the right front rail onto proper location by having the square nuts pass through the slot of the front rail. Repeat for the left front rail.

5.Attach the middle plug (8) to connect the two front rail halves.

6.With the blade installed, use the rip fence and gauge to adjust the front rail to proper location. When the front rail is level with table, then fix the front rail by tightening the six bolts. NOTE: Place straight edge across table and extension and lift rail until edge is flush, then tighten bolts. Repeat for other side.

Fig. T

2

2

1 0

0

1

3

– 16 –

6

5

5

7

6

 

 

8

14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Advertencia Léase Este Table of Contents Prohibition Support and Clamp WorkPower Tool Safety General Safety Instructions Before Using this Power ToolTable SAW Safety Kickbacks Electrical Requirements and Safety Power Supply and Motor SpecificationsGrounding Instructions Guidelines for Extension CordsVolt Single Phase Operation Supplied Not SuppliedCarton Contents Unpacking Your Table SAW Know Your Table SAW Glossary of Terms Assembly and Adjustments Assembling Stand FIG. A~IAssembling Table SAW to Stand FIG. J Moving Table SAW and Stand FIG. JAnti-kickback pawl storage Fig. L Storage FIG. L ~ RRiving knife storage Fig. P Power cord storage Fig. R Fig. P Miter gauge storage Fig. QInstalling a Blade FIG. W Adjusting the 90 and 45 Positive Stops FIG. X, Y, ZBlade Tilting Handwheel FIG Blade Elevation Handwheel FIGBlade Tilting Indicator FIG. AA Stop Fig. X, Y 45º Stop Fig. X, ZFig. BB Installing Blade Guard Assembly FIG. FF, GG Fig. EEInstalling the Miter Gauge Adjusting the Miter Gauge FIG. HHInstalling the RIP Fence FIG RIP Fence Adjustment FIG. JJFig. KK Operation Basic SAW OperationsSetting Bevel Angle FIG. QQ Cutting OperationsRipping FIG. PP Bevel RippingRipping Small Pieces Using Wood Facing on the Miter GaugeCrosscutting FIG. RR Bevel Crosscutting FIG. TT Using Wood Facing on the RIP Fence FIG. WWMiter Cuts FIG 240V Operation Changing Wires FIG. YY, ZZ Dado Cuts FIGFig. ZZ Maintenance General MaintenanceMaintaining Your Table SAW LubricationReplacement Parts Service and Repairs Troubleshooting GuideProblem Possible Causes Corrective Action Accessories Accessories and Attachments2WHW Dado Insert Plate Push Stick Pattern Push Stick ConstructionParts List MM Stationary Table SAW Parts List for Table SAWMM Table SAW Schematic for Table SAW MM Stationary Table SAW Parts List & Schematic for Stand Description Size QtyMM Stationary Table SAW Parts List & Schematic for Motor TerminalPage Warranty Three Year Limited Warranty
Related manuals
Manual 38 pages 37.67 Kb
Top Page Image Contents