Porter-Cable PCB270TS Assembling Table SAW to Stand FIG. J, Moving Table SAW and Stand FIG. J

Page 14

9.Bag “I” - Mount the pedal (1) to the caster bracket

(2)by using the longest bolt (3) and nut (4), and attach the link (5) to pedal (1) with bolt (6) and nut

(4)by 6 mm hex key supplied.

Fig. F

5

4

6

Right side

 

1

 

view

 

 

4

3

2

10.Bag “I” - Attach the left / right rear tubes (8) of caster bracket into the brackets (9) of the rear legs by using two short bolts (10). Attach the link (5) into the bracket (11) with bolt (6) and nut (4).

NOTE: Do not over tighten bolts. The caster assembly will be difficult to operate if the bolts are too tight.

Fig. G

 

 

 

9

11

 

 

 

4

5

8

10

 

 

 

 

6

 

 

NOTE: The front right / left legs have been removed from this drawing for illustration purposes only.

11.Bag “J, K” - Attach miter gauge storage (12) to the right leg support by using two short screws (14) and nuts (15).

13.Insert the rip fence storage (20) into slots (21) of the left leg support, tighten by using two of six screws (22).

Fig. I

18

16

 

22

15

 

 

 

20

 

 

 

21

NOTE: Make sure all screws and nuts are tight and stand is on a stable surface before mounting saw.

!WARNING

Although compact, this saw is heavy and should be lifted with care. Get the assistance of someone to lift and move the saw.

!WARNING

For your safety, never connect plug to power source receptacle until all assembly and adjustment steps are complete, and you have read and understood the safety instructions.

ASSEMBLING TABLE SAW TO STAND (FIG. J)

1.Lift the saw body (1) and place on the stand (2), aligning the mounting grooves (3) of the saw base with the four mounting holes on the top plate of stand.

2.Bag “P” - Attach the table saw to the stand with four hex head bolts (4).

3.Tighten all mounting bolts with a wrench.

Fig. J

Fig. H

12

15

14

4

1

3

2

12.Bag “J, K” - Attach power cord storage (16) to the left leg support by using two long screws (18) and nuts (15).

5

6

MOVING TABLE SAW AND STAND (FIG. J)

1.Tread on the area (5) of pedal to lift the saw and stand when stand legs contacting the level surface.

2.Move the saw and stand to the desired location by the caster assembly for operation or storage.

3.Tread on the area (6) of pedal to put the saw and stand on the ground.

–14 –

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Advertencia Léase Este Table of Contents Prohibition Support and Clamp WorkPower Tool Safety General Safety Instructions Before Using this Power ToolTable SAW Safety Kickbacks Grounding Instructions Electrical Requirements and SafetyPower Supply and Motor Specifications Guidelines for Extension CordsVolt Single Phase Operation Supplied Not SuppliedCarton Contents Unpacking Your Table SAW Know Your Table SAW Glossary of Terms Assembly and Adjustments Assembling Stand FIG. A~IAssembling Table SAW to Stand FIG. J Moving Table SAW and Stand FIG. JRiving knife storage Fig. P Storage FIG. L ~ RAnti-kickback pawl storage Fig. L Power cord storage Fig. R Fig. P Miter gauge storage Fig. QBlade Tilting Handwheel FIG Installing a Blade FIG. WAdjusting the 90 and 45 Positive Stops FIG. X, Y, Z Blade Elevation Handwheel FIGBlade Tilting Indicator FIG. AA Stop Fig. X, Y 45º Stop Fig. X, ZFig. BB Installing Blade Guard Assembly FIG. FF, GG Fig. EEInstalling the RIP Fence FIG Installing the Miter GaugeAdjusting the Miter Gauge FIG. HH RIP Fence Adjustment FIG. JJFig. KK Operation Basic SAW OperationsRipping FIG. PP Setting Bevel Angle FIG. QQCutting Operations Bevel RippingCrosscutting FIG. RR Using Wood Facing on the Miter GaugeRipping Small Pieces Miter Cuts FIG Using Wood Facing on the RIP Fence FIG. WWBevel Crosscutting FIG. TT 240V Operation Changing Wires FIG. YY, ZZ Dado Cuts FIGFig. ZZ Maintaining Your Table SAW MaintenanceGeneral Maintenance LubricationProblem Possible Causes Corrective Action Troubleshooting GuideReplacement Parts Service and Repairs 2WHW Dado Insert Plate Accessories and AttachmentsAccessories Push Stick Pattern Push Stick ConstructionParts List MM Stationary Table SAW Parts List for Table SAWMM Table SAW Schematic for Table SAW MM Stationary Table SAW Parts List & Schematic for Stand Description Size QtyMM Stationary Table SAW Parts List & Schematic for Motor TerminalPage Warranty Three Year Limited Warranty
Related manuals
Manual 38 pages 37.67 Kb
Top Page Image Contents