Porter-Cable 362V instruction manual General Safety Rules, Additional Specific Safety Rules

Page 1

Instruction Manual

Manuel d’utilisation

Manual de Instrucciones

360, 360VS, 361, 362, 362V, 362VSK, 363

Belt Sander

Ponceuses à bande

Lijadoras de correa

www.porter-cable.com

®

Copyright © 2006 Porter-Cable

 

 

Part No. A17406 - 04-24-06 - Rev. A

 

Instructivo de operacion,

 

centros de servicio y poliza de garantia.

 

ADVERTENCIA: Lease este instructivo antes de usarel producto.

SAVE THESE INSTRUCTIONS!

Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

To reduce the risk of injury, user must read instruction manual.

GENERAL SAFETY RULES

1)Work area safety

a)Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2)Electrical safety

a)Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec- trician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. Applicable only to Class I (grounded) tools.

b)Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electri- cian to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Applicable only to Class II (double insulated) tools.

c)Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

d)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

e)Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. Use only 3-wire extension cords that have 3- prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug.

f)When operating a power tool outdoors, use an extension cord suitable for outdoor use. If an extension cord is to be used outdoors, it must be marked with the suffix W-A or W following the cord type designation. Use of a cord suitable for outdoor use reduces the risk of electric shock. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line volt- age resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

 

 

120V

0-25

26-50

51-100

101-150

 

 

 

 

Ampere Rating

Gauge of wire in AWG units

 

 

10 to 12 amps

16

16

14

12

12 to 16 amps

14

12

Not recommended

3)Personal safety

a)Stay alert, watch what you are doing and use common sense when operating a pow- er tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b)Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

c)Avoid accidental starting. Be sure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f)Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards. Accessories that may be suitable for one tool, may become haz- ardous when used on another tool.

4)Power tool use and care

a)Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

b)Do not force the power tool. Use the correct power tool for your application. The cor- rect power tool will do the job better and safer at the rate for which it was designed.

c)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

d)Disconnect the plug from the power source before making any adjustments, chang- ing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

e)Store idle power tools out of the reach of children and do not allow persons unfamil- iar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

f)Maintain power tools. Check for misalignment or binding of moving parts, break- age of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

g)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

h)Use the power tool, accessories and tool bits etc., in accordance with these instruc- tions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5)Service

a)Have your power tool serviced by a qualified repair person using only identical re- placement parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

Do not sand metal of any kind with your belt sander. Sparks may be generated by sanding screws, nails or other metals which may ignite dust particles.

Do not wet sand with this sander. Liquids may enter the motor housing and cause electric shock.

Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

Clean out your tool often, especially after heavy use. Dust and grit containing metal particles often accumulate on interior surfaces and could create a risk of serious injury, electric shock or electrocution.

Use proper safety equipment. Wear safety goggles for eye protection, wear hearing protection, and wear a protective mask to minimize breathing in the fine dust created while sanding.

Always disconnect the sander cord plug from the power circuit before changing belts. Such preventive safety measures reduce the risk of starting the power tool accidentally.

Sanding of lead-based paint is not recommended. Lead-based paint should only be removed by a professional.

Always maintain a firm grip on the belt sander handles with both hands to prevent loss of con- trol.

Do not operate belt sander without all guards and covers securely in place.

Some dust created by power sanding, sawing, grinding, drilling, and other con- struction activities contains chemicals known to cause cancer, birth defects or other repro- ductive harm.

Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection ap- propriate for the dust exposure. Direct particles away from face and body.

Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

SYMBOLS

 

 

 

 

 

 

The label on your tool may include the following symbols:

 

 

V

volts

A

amps

Hz

hertz

W

watts

min

minutes

 

 

 

or a.c alternating current

 

 

 

 

.. direct current

no

no load speed

.......

class II tool

 

 

 

 

...........protective earth

./min

revolutions per minute

 

 

 

 

 

 

 

 

 

 

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Young and unborn children are particularly vulnerable.

Before beginning any paint removal process you should determine whether the paint you are removing contains lead. This can be done by your local health department or by a professional who uses a paint analyzer to check for lead.

Lead-based paint should only be removed by a professional.

Persons removing paint should follow these guidelines:

1.Keep the work area well ventilated. Open the windows and put an exhaust fan in one of them. Be sure the fan is moving air from inside to outside.

2.Remove or cover any carpets, rugs, furniture, clothing, cooking utensils, and air ducts. Such preventive safety measures reduce the risk of exposure.

3.Place drop cloths in the work area to catch any paint chips or peelings. Wear protective clothing such as extra work shirts, overalls and hats. Such preventive safety measures reduce the risk of exposure.

4.Work in one room at a time. Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths.

5.Children, pregnant (or potentially pregnant) women and nursing mothers should not be present in the work area until the work is done and all cleanup is complete. Such preventive safety measures reduce the risk of injury.

6.Wear a dust respirator or a dual filter (dust and fume) respirator mask which has been approved by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health (NIOSH), or the United States Bureau of Mines. These masks and replaceable filters are readily available at major hardware stores. Be sure the mask fits. Beards and facial hair may keep the masks from sealing properly. Change filters often.

Image 1
Contents Additional Specific Safety Rules General Safety RulesAdditional Safety Rules for Paint Removal 360, 360VS, 361, 362, 362V, 362VSKTroubleshooting Maintenance AssemblyService AccessoriesSymboles Calibre de fil minimum recommandé pour les rallongesConserver CES Directives Règles Générales SUR LA Sécurité¡CONSERVE Estas Instrucciones Montaje Normas DE Seguridad Específicas AdicionalesOperación Servicio Guia Localizacion DE Fallas MantenimientoAccesorios Garantia