installation, start-up and
service instructions569C
COMMERCIAL
576B
IMPORTANT — READ BEFORE INSTALLING
1.Read and become familiar with these installation instructions before installing this unit (Fig. 1).
2.Be sure the installation conforms to all applicable local and national codes.
3.These instructions contain important information for the proper maintenance and repair of this equipment. Retain these instructions for future use.
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 1
I. Locate the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
II. Rig and Place Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
III. Compressor Mounting. . . . . . . . . . . . . . . . . . . . . . . . 2
IV. Unit Refrigerant Piping Connections. . . . . . . . . . . . 2
V. Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . 5
VI. Accessory Installation. . . . . . . . . . . . . . . . . . . . . . . . 8
Cancels: II | II |
| 8/15/00 |
Fig. 1 — Typical Unit (569C072 Shown)
I.
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 9
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
II. Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
III.
IV. Capacity Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
V. Compressor Removal . . . . . . . . . . . . . . . . . . . . . . . 11
VI. Crankcase Heater . . . . . . . . . . . . . . . . . . . . . . . . . . 11
VII. Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . . . . 11
VIII. Refrigerant Service Ports . . . . . . . . . . . . . . . . . . . . 12
IX. High Flow Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . 13,14
SAFETY CONSIDERATIONS
WARNING: Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electric shock, or other occurrences which may injure you or damage your property. Con- sult a qualified installer or service agency for informa- tion or assistance. The qualified installer or agency must use only
Recognize safety information. This is the
Understand the signal words — DANGER, WARNING, and CAUTION. These words are used with the
WARNING: Before performing service or mainte- nance operations on unit, turn off main power switch to unit. Electrical shock could cause personal injury.
1.The power supply (volts, hertz, and phase) must cor- respond to that specified on unit rating plate.
2.The electrical supply provided by the utility must be sufficient to handle load imposed by this unit.
3.Refer to the Locate the Unit section on page 2 and Fig. 2 and 3 for locations of electrical inlets, required clearances, and weight distribution based on recom- mended support points before setting unit in place.
4.This installation must conform with local building codes. Refer to local plumbing or wastewater codes and other applicable local codes.