Porter-Cable 4210 & 4212 BOX Joint Bits Readily Available, Dovetail Dado Bits

Page 16

CUTTING THE TAILS

Cut the tail board (drawer side) similar to cutting the rabbeted half-blind dovetail, but remove the spacer and move the left offset guide directly against the tail board.

NOTE: Support the template with a scrap workpiece thick enough to prevent the cutter from contacting the base.

CUTTING THE PINS

Cut the pin board (drawer front) similar to cutting the rabbeted half-blind dovetail. (If you use the alternate method of aligning the pin board with secondary board. Make sure the secondary board does not have a rabbet).

NOTE: Ensure that the pin board (drawer front) is thicker than the depth of cut to prevent the cutter from contacting the base.

FITTING THE JOINT

Fit the joint the same as you would a standard rabbeted half-blind dovetail.

NOTE: If a change in depth-of-cut is required, change it on both bits.

BOX JOINT BITS

You can make box joints with different diameter router bits for the two workpieces. The process is identical to making standard box joints except that you will need to change the bit for the second board. Two routers will make this job easier. However, this two-router method will require two 3/4" OD template guides and two template guide lock nuts, available from Porter-Cable.

In selecting straight bits for these modified box joints, keep in mind the following:

1.The sum of the diameters of the two straight bits must equal 1".

2, The length of the bit used to cut the first board determines the maximum thickness of the second board. (Example: if a 3/8" diameter bit used on the first board has a 1/2" long cutter, the maximum thickness of the second board would be 1/2").

BOX JOINT BITS (READILY AVAILABLE)

LARGER STRAIGHT BIT

 

SMALLER STRAIGHT BIT

 

 

 

1/2" 1/2"

9/16" 7/16"

5/8" 3/8"

DOVETAIL DADO BITS

Any dovetail bit can be used to make dovetail dados (sliding dovetails) as long as the bit does not cut into the template guide or the base of the jig. The process is identical to that of the standard dovetail dado. Also, you can use template guides smaller than 3/4" OD which will have the effect of making the dado slot wider than the bit diameter.

NOTE: Any template guide bushing surface must not extend more than 1/4" from the base.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Supplementary Instructiondovetail JIG Manual Table of Contents Safety Guidelines Definitions Important Safety InstructionsReplacement Parts Additional Safety RulesBackground Information Operation Miscellaneous TechniquesTemplates Mounted to Clamping Boards SetupTHROUGH-DOVETAILS with Clamping Boards Cutting the Pins Cutting the TailsTHROUGH-DOVETAILS with Unlimited Board Width Fitting the JointSet the router bit depth, using the pencil mark from Step Fitting the joint is identical to the previous section a HALF-BLIND Dovetails with Clamping Boards Blind Dovetails with Tail Boards Thicker than 7/8Cutting the Joint Using a Router Table THROUGH-DOVETAIL Bits Alternate Router BitsTHROUGH-DOVETAIL BIT Combinations Readily Available HALF-BLIND Dovetail BIT Readily Available BOX Joint Bits Readily Available BOX Joint BitsDovetail Dado Bits HALF-BLIND Dovetails with Tail Boards Thicker than 7/8 Mitering the Pins Mitered THROUGH-DOVETAILTHROUGH-DOVETAIL, SKIPPED-PIN Method Mitering the TailsHALF-BLIND DOVETAIL, Skipped PIN Method Cutting the Pins Page Cutting the Tails Multiple Spacer Method END-TO-END JointsFitting and Cutting the Joint BOX END-TO-END JointsDrawers with Dovetail Dados Dovetail END-TO-END JointsWooden Hinges Hinges with a Drilled HoleHinges with ROUTER-MADE Grooves Hinges with ROUTER-MADE Grooves Angled Joints Setup with the Template Mounted to the Base of the JIGObtuse Angled Joints Setup with the Template Mounted to a Clamping Board Cutting the TailsCutting the Pins Acute Angled Joints SLANTED-SIDE Joints COMPOUND-ANGLE Joints Setup Blade Tilt Angle Make Angled CUT Inlayed Through Dovetail Inlayed JointsMake the First Joint CUT OFF the Inlay Board Inlayed HALF-BLIND DovetailMake the Second Joint 100 13/128 050 042 028 014 Inlayed BOX Joint Tables of Commonly Available Router BIT Sizes Through Dovetail Router BIT CombinationsHALF-BLIND Dovetail Bits BOX Joint BIT CombinationsService Troubleshooting MaintenanceAccessories Warranty PORTER-CABLE Limited ONE Year WarrantyCanadian PORTER-CABLE Delta Service Centers Michigan

4210 & 4212 specifications

Porter-Cable, a brand renowned for its high-quality power tools, offers a variety of products that cater to the needs of both professionals and hobbyists. Among its notable products are the Porter-Cable 4210 and 4212 Dovetail Jigs, which stand out for their precision, versatility, and user-friendly design. These jigs are essential for woodworking enthusiasts looking to create strong and visually appealing dovetail joints.

The Porter-Cable 4210 Dovetail Jig is designed with simplicity and ease of use in mind. It features a robust aluminum base that provides stability during operation, ensuring accurate cuts every time. One of its standout features is the built-in template system, allowing users to create half-blind, through, and box dovetails without hassle. The adjustable pins and tail spacing facilitate a variety of joint sizes, making it suitable for different projects, whether you’re building fine furniture or cabinetry.

Another remarkable feature of the 4210 is its user-friendly setup. The jig's intuitive design allows users to quickly adjust the settings for various woodworking applications, saving time and effort. The depth stop feature provides precise control over the cutting depth, allowing for consistent results that meet high-quality standards. The Porter-Cable 4210 is powered by a router, which adds to its versatility, enabling the creation of different joint types with ease.

The Porter-Cable 4212 Dovetail Jig takes the capabilities of the 4210 and brings them to the next level. This model offers enhanced features, including a more advanced template system that allows for greater customization and flexibility. The 4212 includes templates for both through and half-blind dovetails along with box joints, making it a comprehensive solution for woodworkers seeking variety in joint design.

Both jigs are equipped with a sturdy carrying case for portability, making them ideal for those who need to transport their tools to job sites or workshops. Additionally, the durable construction of both models ensures they can withstand the rigors of frequent use. Users appreciate the quality craftsmanship that Porter-Cable has maintained in both models.

Overall, the Porter-Cable 4210 and 4212 Dovetail Jigs are excellent additions to any woodworker's toolkit. With their combination of precision, ease of use, and versatility, they empower users to create professional-quality dovetail joints with confidence. Whether you are a beginner or an experienced craftsman, these jigs offer the reliability and performance necessary to enhance your woodworking projects.
Top Page Image Contents